Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 24

Страница: 24 / 100

Operation options

iTEMP TMT85

Hauser

Operation options

6.1

Overview of operation options

Operators have a number of options for configuring and commissioning the device:

1. Configuration programs

FF functions and device-specific parameters are configured via the fieldbus interface.

Special configuration and operating programs are available from various manufacturers for

this purpose.

2. Miniature switches (DIP switches) for diverse hardware settings, optional

→  25
The following hardware settings for the FOUNDATION Fieldbus

interface can be made

using DIP switches on the rear of the optional display:
• Enabling/disabling the simulation mode in the Analog Input function block

• Switching the hardware write protection on/off

• Switching (rotating) the display by 180 °

A0041955

 11

Operation options for the head transmitter

Configuration/operating programs for operation via FOUNDATION Fieldbus

(fieldbus functions, device

parameters)

DIP switches for hardware settings on the rear of the optional display (write protection, simulation mode)

For the head transmitter, display and operating elements are available locally only if

the head transmitter was ordered with a display unit!

Содержание iTEMP TMT85





































































































Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды

Endress+Hauser iTEMP TMT85, Руководство по эксплуатации

Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды