Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 100

background image

Operation via FOUNDATION Fieldbus

TM

iTEMP TMT85

86

Hauser

Parameter

Write access
with operating
mode
(MODE_BLK)

Description

Actual Status Number /
Previous Status Number
(ACTUAL_ STATUS_
NUMBER / PREVIOUS_
STATUS_ NUMBER)

Read only /
AUTO - OOS

Current/previous status number:
000 NO_ERROR: No error is present
041 SENSOR_BREAK: Sensor break
043 SENSOR_SHORTCUT: Sensor short-circuit
042 SENSOR_CORROSION: Corrosion of terminals or sensor
cables
101 SENSOR_UNDERUSAGE: Sensor measured value is below
the linearization range
102 SENSOR_OVERUSAGE: Sensor measured value is above
the linearization range
104 BACKUP_ACTIVATED: Backup function activated due to
sensor failure
103 DEVIATION: Sensor drift detected
501 DEVICE_PRESET: Reset routine in progress
482 SIMULATION: Device is in the simulation mode
402 STARTUP: Device is in the startup/initialization phase
502 LINEARIZATION: Linearization incorrectly selected or
configured
901 AMBIENT_TEMPERATUR_LOW: Ambient temperature
too low; DEVTEMP_VALUE < –40 °C (–40 °F)
902 AMBIENT_TEMPERATURE_HIGH: Ambient temperature
too high; DEVTEMP_VALUE > 85 °C (185 °F)
261 ELECTRONICBOARD: Electronics module/hardware
faulty
431 NO_CALIBRATION: Calibration values lost/modified 283
MEMORY_ERROR: Contents of memory inconsistent
221 RJ_ERROR: Error in reference junction measurement/
internal temperature measurement

Actual Status Channel /
Previous Status Channel
(PREVIOUS/ ACTUAL_
STATUS_ CHANNEL)

Read only /
AUTO - OOS

ACTUAL_STATUS_CHANNEL displays the channel that
currently has the error with the highest value.
PREVIOUS_STATUS_CHANNEL indicates the channel where
an error last occurred.

Actual Status Description /
Previous Status Description
(PREVIOUS/ ACTUAL_
STATUS_DESC)

Read only /
AUTO - OOS

Displays the descriptions of the current and previous error
status.



The descriptions can be taken from the description for
the Actual Status Number/ Previous Status Number
parameter.

Actual Status Count
(ACTUAL_ STATUS_
COUNT)

Read only

The number of status messages currently active in the device.

Primary Value 1 Max.
Indicator PV1_MAX_
INDICATOR

AUTO - OOS

Indicator for the maximum value to occur for PV1, can be
reset by writing any value in this parameter.

Primary Value 1 Min.
Indicator PV1_MIN_
INDICATOR

AUTO - OOS

Indicator for the minimum value to occur for PV1, can be
reset by writing any value in this parameter.

Primary Value 2 Max.
Indicator PV2_MAX_
INDICATOR

AUTO - OOS

Indicator for the maximum value to occur for PV2, can be
reset by writing any value in this parameter.

Primary Value 2 Min.
Indicator PV2_MIN_
INDICATOR

AUTO - OOS

Indicator for the minimum value to occur for PV2, can be
reset by writing any value in this parameter.

Sensor 1 Max. Indicator
SV1_MAX_ INDICATOR

AUTO - OOS

Indicator for the maximum value to occur at sensor 1, can be
reset by writing any value in this parameter.

Sensor 1 Min. Indicator
SV1_MIN_ INDICATOR

AUTO - OOS

Indicator for the minimum value to occur at sensor 1, can be
reset by writing any value in this parameter.

Sensor 2 Max. Indicator
SV2_MAX_ INDICATOR

AUTO - OOS

Indicator for the maximum value to occur at sensor 2, can be
reset by writing any value in this parameter.

«
...
84
85
86
87
88
...
»

Содержание iTEMP TMT85





































































































Отзывы:

Нет отзывов

Похожие инструкции для iTEMP TMT85

Бренд: Kawai Страницы: 5

Бренд: Jata hogar Страницы: 12

Бренд: Bartington Страницы: 15

Бренд: Bartec Страницы: 216

Бренд: YOKOGAWA Страницы: 2

Бренд: DAVIS Страницы: 12

Бренд: Lumel Страницы: 32

Бренд: Larson Davis Страницы: 536

Бренд: National Instruments Страницы: 15

Бренд: Waterproof Страницы: 10

Бренд: Ocean Optics Страницы: 43

Бренд: Ocean Technology Systems Страницы: 12

Бренд: Ocean Reef Страницы: 24

Бренд: Unitech Страницы: 18

DUSTHUNTER C200

Бренд: SICK Страницы: 126

Бренд: Axio MET Страницы: 5

PRO VPR100 Series

Бренд: CTC Union Страницы: 10

Бренд: PCB Piezotronics Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды