Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 69

Страница: 69 / 100

iTEMP TMT85

Operation via FOUNDATION Fieldbus

Hauser

Resource Block

Parameter

Index

Parameter

Write access with
operating mode
(MODE_BLK)

Description

Confirm Time
(CONFIRM_TIME)

AUTO - OOS

Specify the confirmation time for the event report. If the device does not
receive confirmation within this time, the event report is sent to the fieldbus
host system again.

Factory setting:

640000 1/32 ms

Cycle Selection (CYCLE_SEL)

AUTO - OOS

Displays the block execution method used by the fieldbus host system.



The block execution method is selected by the fieldbus host system.

Cycle Type (CYCLE_TYPE)

Read only

Displays the block execution methods supported by the device.

Display:

SCHEDULED
Scheduled block execution method
BLOCK EXECUTION
Sequential block execution method
MANUF SPECIFIC
Manufacturer-specific

DD Resource (DD_RESOURCE)

Read only

Displays the source for the device description in the device.

Display:

(blank spaces)

DD Revision (DD_REV)

Read only

Displays the revision number of the ITK-tested device description.

Device Revision (DEV_REV)

Read only

Displays the revision number of the device.

Device Tag (DEVICE_TAG)

Read only

Tag name/device TAG.

Device Type (DEV_TYPE)

Read only

Displays the device ID number in hexadecimal format.

Display:

0x10CE (hex) for TMT85

Electronic Name Plate Version
(ENP_VERSION)

Read only

Version of the ENP (electronic name plate).

Fault State (FAULT_STATE)

Read only

Current status display of the fault state of the Analog Output and Discrete
Output function blocks.

Check Active
(FD_CHECK_ACTIVE)

Read only

Indicates whether a diagnostic event of the defined category is currently
pending.

Check Alarm (FD_CHECK_ALM) AUTO - OOS

Alarms that are actively transmitted by the device to the fieldbus.

Check Map (FD_CHECK_MAP)

AUTO - OOS

Enable or disable diagnostic events or diagnostic groups for the relevant
category.

Check Mask
(FD_CHECK_MASK)

AUTO - OOS

Disables the transmission of device messages to the fieldbus.

Check Priority (FD_CHECK_PRI) AUTO - OOS

Indicates the alarm priority of the alarm transmitted to the fieldbus.

Fail Active (FD_FAIL_ACTIVE)

Read only

Indicates whether a diagnostic event of the defined category is currently
pending.

Fail Diagnostic Alarm
(FD_FAIL_ALM)

AUTO - OOS

Alarms that are actively transmitted by the device to the fieldbus.

Fail Map (FD_FAIL_MAP)

AUTO - OOS

Enable or disable diagnostic events or diagnostic groups for the relevant
category.

Fail Mask (FD_FAIL_MASK)

AUTO - OOS

Disables the transmission of device messages to the fieldbus.

Fail Priority (FD_FAIL_PRI)

AUTO - OOS

Indicates the alarm priority of the alarm transmitted to the fieldbus.

Maintenance Active
(FD_MAINT_ACTIVE)

Read only

Indicates whether a diagnostic event of the defined category is currently
pending.

Maintenance Alarm
(FD_MAINT_ALM)

AUTO - OOS

Alarms that are actively transmitted by the device to the fieldbus.

Maintenance Map
(FD_MAINT_MAP)

AUTO - OOS

Enable or disable diagnostic events or diagnostic groups for the relevant
category.

Содержание iTEMP TMT85





































































































Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды

Endress+Hauser iTEMP TMT85, Руководство по эксплуатации

Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды