Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 100

background image

iTEMP TMT85

Operation via FOUNDATION Fieldbus

TM

Hauser

87

Parameter

Write access
with operating
mode
(MODE_BLK)

Description

Sensor 2 Min. Indicator
SV2_MIN_ INDICATOR

AUTO - OOS

Indicator for the minimum value to occur at sensor 2, can be
reset by writing any value in this parameter.

Device Temperature Max.
Indicator DEVTEMP_ MAX_
INDICATOR

AUTO - OOS

Indicator for the maximum value to occur at the internal
reference temperature measuring point, can be reset by
writing any value in this parameter.

Device Temperature Min.
Indicator DEVTEMP_MIN_
INDICATOR

AUTO - OOS

Indicator for the minimum value to occur at the internal
reference temperature measuring point, can be reset by
writing any value in this parameter.

CONFIG_
AREA_1...CONFIG_
AREA_15

OOS

The configurable area of FOUNDATION Fieldbus field
diagnostics. One of the four diagnostic events:
• 42 - Corrosion
• 103 - Drift
• 901 - Ambient temperature too low
• 902 - Ambient temperature too high
can be separated from the factory-configured diagnostic
group and categorized individually here. By setting the event
to one of the Field Diagnostic Bits 1-15, the category for this
bit can be configured in the Resource Block to one of the
categories F, C, S, M (→  93).

STATUS_SELECT_ 42

OOS

The measured value status (BAD, UNCERTAIN, GOOD) can be
configured for the individual diagnostic event

STATUS_SELECT_ 103

OOS

STATUS_SELECT_ 901

OOS

STATUS_SELECT_ 902

OOS

DIAGNOSIS_ SIMULATION_
ENABLE

OOS

Enable/disable simulation of a diagnostic event.

DIAGNOSIS_ SIMULATION_
NUMBER

AUTO - OOS

Use this function to select the diagnostic event to be
simulated.

14.3.9 Transducer Block "Display"

The settings in the "Display" Transducer Block make it possible to display measured values

from the two Transducer Blocks "Sensor 1 + 2" on the optional display. The selection is

made via the DISPLAY_SOURCE_X1 parameter. The number of decimal places displayed

can be configured independently for every channel using the DISP_VALUE_X_FORMAT

parameter. Symbols are available for the units °C, K, F, %, mV, R and Ω. These units are

displayed automatically when the measured value is selected.
The "Display" Transducer Block can show up to 3 values alternately on the display. The

display automatically switches between the values after a configurable time interval

(between 6 and 60 seconds), which can be set in the ALTERNATING_TIME parameter.

Transducer Block “DISPLAY” (device-specific parameters)

Parameter

Write access with
operating mode
(MODE_BLK)

Description

Alternating time
ALTERNATING_TIME

AUTO - OOS

Entry (in s) specifying how long a value should be shown on
the display. Setting from 6 to 60 s.

Display value x
DISP_VALUE_X1)

Read only

Selected measured value:
• Status
• Value

«
...
85
86
87
88
89
...
»

Содержание iTEMP TMT85





































































































Отзывы:

Нет отзывов

Похожие инструкции для iTEMP TMT85

Бренд: Callaway Страницы: 11

Бренд: ZHYQ Страницы: 6

Бренд: Danfoss Страницы: 80

Бренд: EPE Conseil Страницы: 3

Бренд: Primes Страницы: 48

iTrans 77023554

Бренд: Industrial Scientific Страницы: 94

Бренд: Vectronics Страницы: 2

Бренд: Resol Страницы: 24

LiveTester LT 220

Бренд: StarLogixs Страницы: 7

Intelligizer Fence Monitor

Бренд: Zareba Страницы: 8

WTW SensoLyt 900

Бренд: Xylem Страницы: 12

FTCI-3/4D15A4P-2LUX-H1141

Бренд: turck Страницы: 2

Бренд: Campbell Страницы: 20

Beta 10P Series

Бренд: ST Страницы: 32

Dynasonics IS-4000

Бренд: Badger Meter Страницы: 36

Бренд: MTE Страницы: 113

Backsense BS-9000-WD

Бренд: Brigade Страницы: 42

Бренд: Cargo Data Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды