Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 47

Страница: 47 / 100

iTEMP TMT85

Accessories

Hauser

11.2 Return

The requirements for safe device return can vary depending on the device type and

national legislation.

1. Refer to the website for more information:

http://www.endress.com/support/return-material

2. Return the device if repairs or a factory calibration are required, or if the wrong

device was ordered or delivered.

11.3 Disposal

If required by the Directive 2012/19/EU on waste electrical and electronic equipment

(WEEE), the product is marked with the depicted symbol in order to minimize the

disposal of WEEE as unsorted municipal waste. Do not dispose of products bearing this

marking as unsorted municipal waste. Instead, return them to Hauser for

disposal under the applicable conditions.

Accessories

Various accessories, which can be ordered with the device or subsequently from Endress

+Hauser, are available for the device. Detailed information on the order code in question is

available from your local Hauser sales center or on the product page of the

Hauser website:

www.endress.com

Accessories included in the scope of delivery:

• Printed copy of the Brief Operating Instructions

• ATEX supplementary documentation: ATEX Safety instructions (XA),

ontrol

rawings

(CD)

• Mounting material for head transmitter

• Mounting material for field housing (wall or pipe mounting) as option

12.1 Device-specific accessories

Accessories

TID10 display unit for Hauser head transmitter iTEMP TMT8x

, attachable

TID10 service cable for the remote operation of the display for service purposes; length 40 cm

Field housing TA30x for Hauser head transmitter

Adapter for DIN rail mounting, DIN rail clip as per IEC 60715 (TH35) without securing screws

Standard - DIN mounting set (2 springs, 4 lock washers and 1 display connector cover)

US - M4 securing screws (2 M4 screws and 1 display connector cover)

Fieldbus connector
(FF):

• NPT ½" → 7/8"
• M20 → 7/8"

Stainless steel wall mounting bracket
Stainless steel pipe mounting bracket

Without TMT80

Содержание iTEMP TMT85





































































































Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды

Endress+Hauser iTEMP TMT85, Руководство по эксплуатации

Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды