Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 100

background image

iTEMP TMT85

Operation via FOUNDATION Fieldbus

TM

Hauser

85

In addition, the entire status information of the device and the maximum/minimum

indicators for the two sensor values and the internal temperature are also available.

Transducer Block “ADVANCED DIAGNOSTIC” (device-specific parameters)

Parameter

Write access
with operating
mode
(MODE_BLK)

Description

Corrosion detection
(CORROSION_ DETECTION)

OOS

• OFF: Corrosion detection off
• ON: Corrosion detection on



Only possible for RTD 4-wire connection and
thermocouples (TC).

Sensor Drift monitoring
(SENSOR_
DRIFT_MONITORING)

OOS

Drift between SV1 and SV2 is displayed according to the field
diagnostic configuration of diagnostic event "103 - Drift":
• OFF: Sensor drift monitoring off (diagnostic event 103 has

been deactivated)

• ON: Sensor drift monitoring on (when a drift occurs,

diagnostic event 103 is displayed with the category
configured for the event)

Sensor Drift mode (SENSOR_
DRIFT_MO DE)

OOS

Select whether a status is generated if the value set in the
SENSOR_DRIFT_LIMIT parameter is undershot
(Undershooting) or overshot (Overshooting).



If "Overshooting" is selected, the corresponding
diagnostic event is generated if the limit value is
overshot (SENSOR_DRIFT_LIMIT). In the case of
"Undershooting", the diagnostic event is output if the
limit value is undershot.

Sensor Drift alert value
(SENSOR_
DRIFT_ALERT_VALUE)

OOS

Limit value of the permitted drift from 1 to 999.99.

System Alarm delay
(SYSTEM_ ALARM_DELAY)

OOS

Alarm hysteresis: Value specifying the time a diagnostic
event (F, C, S, M) and measured value status (Bad or
Uncertain) is delayed until the status is output. Can be set
between 0 and 10 seconds.



This setting does not affect the display.

Actual Status Category /
Previous Status Category
(ACTUAL_ STATUS_ CATE
GORY / PREVIOUS_
STATUS_ CATEGORY)

Read only /
AUTO - OOS

Current/last status category
• Good: No errors detected
• F: Failure: Error detected
• C: Function check: Device is in the service mode
• S: Out of Spec.: Device is being operated outside the

specifications

• M: Maintenance required
• Not categorized: No Namur category has been selected for

the current diagnostic event.

«
...
83
84
85
86
87
...
»

Содержание iTEMP TMT85





































































































Отзывы:

Нет отзывов

Похожие инструкции для iTEMP TMT85

Бренд: GE Страницы: 8

Moisture Image 1 Series

Бренд: GE Страницы: 110

DigitalFlow GS868

Бренд: GE Страницы: 74

DigitalFlow GS868

Бренд: GE Страницы: 81

Бренд: Baker Hughes Страницы: 59

Бренд: Baker Hughes Страницы: 2

Бренд: Panametrics Страницы: 67

Бренд: Panametrics Страницы: 108

Transport PT878

Бренд: GE Страницы: 97

Бренд: UEi Страницы: 8

Бренд: Major tech Страницы: 16

Бренд: Zoetis Страницы: 2

Бренд: Teledyne Hastings Instruments Страницы: 54

Бренд: Wavetronix Страницы: 14

Бренд: KALEAS Страницы: 64

Бренд: BYOGuitar.com Страницы: 11

Бренд: Siko Страницы: 2

International 2S Pro

Бренд: Brantz Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды