Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 62

Страница: 62 / 100

Technical data

iTEMP TMT85

Hauser

Field housing

All field housings have an internal geometry in accordance with DIN EN 50446, form B

(flat face). Cable glands in the diagrams: M20x1.5

Maximum ambient temperatures for cable glands

Type

Temperature range

Polyamide cable gland ½" NPT, M20x1.5 (non-Ex)

–40 to +100 °C (–40 to 212 °F)

Polyamide cable gland M20x1.5 (for dust ignition-proof area)

–20 to +95 °C (–4 to 203 °F)

Brass cable gland ½" NPT, M20x1.5 (for dust ignition-proof area)

–20 to +130 °C (–4 to +266 °F)

Fieldbus connector (M12x1 PA, 7/8" FF)

–40 to +105 °C (–40 to +221 °F)

TA30A

Specification

107.5 (4.23)

68.5 (2.7)

(1.1)

78 (3.1)

15.5 (0.6)

A0009820

• Two cable entries
• Temperature: –50 to +150 °C (–58 to +302 °F) without cable

gland

• Material: aluminum, polyester powder coated

Seals: silicone

• Cable entry glands: 1/2" NPT and M20x1.5
• Color of head: blue, RAL 5012
• Color of cap: gray, RAL 7035
• Weight: 330 g (11.64 oz)

TA30A with display window in cover

Specification

107.5 (4.23)

91.6 (3.61)

(1.1)

78 (3.1)

15.5 (0.6)

A0009821

• Two cable entries
• Temperature: –50 to +150 °C (–58 to +302 °F) without cable

gland

• Material: aluminum, polyester powder coated

Seals: silicone

• Cable entry glands: 1/2" NPT and M20x1.5
• Color of head: blue, RAL 5012
• Color of cap: gray, RAL 7035
• Weight: 420 g (14.81 oz)

Содержание iTEMP TMT85





































































































Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды

Endress+Hauser iTEMP TMT85, Руководство по эксплуатации

Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды