DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 226

background image

COMPASS



for molbox™ User’s Manual

Page 149

© 1998-2003

DH Instruments, Inc

.

13.2.4.2

<INSERT SPECIAL CHARACTER>

Use the

<Insert Special Character>

button in the event a nonprintable ASCII

character is a required part of the remote command. When activated the

<ASCII

Characters>

window displays. Select

<Hex>

to select the character using the

hexadecimal value or

<Decimal>

to select based on the decimal value. Most

non-printable characters will display as a square, printable characters will display
as their actual ASCII values. Scroll to the desired character then press the

<Insert>

button. The cursor will turn into a pencil that should be used to point to

the location in which the character should be inserted. Move the cursor to the
proper position in the command string, then click the mouse button.

Figure 86

.

<Insert Special Character>

Panel

13.2.4.3 <COMMAND

TERMINATOR>

Defines how the instrument terminates command strings. The selections
available from the drop down list are carriage return,

<CR>

, and carriage

line feed,

<CR> + <LF>

. The majority of instruments that support an RS-232 or

IEEE-488 interface use carriage line feed as the command terminator.
Refer to the instrument documentation for details.

13.3 RS-232

INTERFACE

RS-232 is one of the most widely used interface standards. At least one RS-232 port is built into every IBM
compatible computer. The interface connects two devices in a full duplex fashion so that both devices
can talk simultaneously. The connection requires that the RS-232 receive line of one device is connected
to the transmit line of the second device and visa versa. In addition to this connection, some devices
require the connection of “handshaking” lines to signal the beginning and the interface conversation.

To set up an RS-232 instrument, an RS-232 cable must be connected between the instrument and the
computer. The port on the computer must be specified along with the settings of the remote instrument.
The computer RS-232 port must be specified and the settings of the port must be adjusted to the settings
of the remote instrument.

COMPASS

provides setup features to facilitate this step. Refer to the

instrument’s manual to determine how to retrieve the RS-232 settings.

13.3.1 RS-232

SETUP

If the remote interface selection is RS-232, the

<RS232 Settings>

screen must be used to

specify the specific setting information. The

<RS232 Settings>

screen is called up in

COMPASS

by clicking any of the RS-232 settings displayed. Select the correct settings for

the device from the drop down lists and click

<OK>

when ready. All settings, with the

exception of the

<COM Port>

, are defined by the device that will use the interface. Refer to

the instruction manual of that device to determine these settings and make any necessary
selections for the interface to function in RS-232. The

<COM Port>

selection should

«
...
161
162
163
164
165
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

Бренд: MACROMEDIA Страницы: 156

Бренд: Sanford Страницы: 122

Бренд: SanDisk Страницы: 11

DREAMWEAVER 8-EXTENDING DREAMWEAVER

Бренд: MACROMEDIA Страницы: 504

DATA SYNCHRONIZER

Бренд: Novell Страницы: 50

Бренд: Primera Страницы: 19

Бренд: Brother Страницы: 24

MacBroidery„ Embroidery Lettering Software for Mac

Бренд: Brother Страницы: 56

Бренд: Brother Страницы: 48

Бренд: Brother Страницы: 272

Бренд: Brother Страницы: 200

Бренд: Sawgrass Страницы: 48

CLOUD DIRECTOR 1.0

Бренд: VMware Страницы: 3

VmWare ESX Server 2.12 Deployment

Бренд: VMware Страницы: 34

Бренд: VMware Страницы: 34

Active Management Technology v5.0

Бренд: Intel Страницы: 143

Бренд: ACT Страницы: 124

00308-011408-9F30A - VLA AUTOSKETCH R8-MEDIA W9X/NT

Бренд: Autodesk Страницы: 400

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды