DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 226

background image

COMPASS



for molbox™ User’s Manual

© 1998-2003

DH Instruments, Inc

.

Page 30

The Status Bar is located at the bottom of the main screen. In all run modes,

COMPASS

flashes information

related to the current operation on this display. While running tests, two panels and a progress indicator
also display with status information on the current test step and point. The blue panel on the left displays
the current test step or function. Each point of a test sequence has five basic test steps:

molbloc Change

(if specified for this point in Test Definition)

•

Purge

(if specified for this molbloc change)

•

Leak Test

(if specified for this molbloc change)

Set

Flow

to flow point specified

Stability

Test

for flow to stabilize at the set point

•

Tare

(if specified for this point)

•

Jog Flow

(if specified for this point)

Dwell

for dwell time at the set point

Take

Point

for length of averaging time

The red panel displays the current test point during a test. The notation used is “current cycle. current
point <of> total cycles. total points per cycle”. Multiple readings per point information is not included in
this display. For example, if a 2 cycle 10 point test is executed, point 3 of the 1

st

cycle displays as “1.3 of 2.10”.

Refer to these displays to determine the new current point, when the

<Skip Back>

and

<Skip Forward>

buttons are used.

The progress indicator is a visual indication of the relationship between the current test point and the
number of points in a test. The left side of the progress bar represents 0 progress and the right side
represents 100 %. Each step and reading of a test point increments the progress indicator. When

<Skip Back>

and

<Skip Forward>

buttons are used, the progress indicator also reflects the current position.

Figure 13.

Status Bar

6.4 RUN

MODES

Run mode describes the automatic execution function that

COMPASS

is in. Typically, instruments are polled

over their remote interface while in a run mode. The top of the main screen always displays the current
run mode. All run modes support the ability to log data to a data file.

COMPASS

has four run modes:

1.

Idle

- No run mode is active. Menu items such is

[Setup]

can only be accessed in this mode. They

are not available in active run modes.

2.

Run molbox

- Activated by the

[Run]

,

[Run molbox]

menu option. This run mode is to work with the

molbox without a DUT and without a Test Definition (see Section 7.3).

3.

Run DUT

- Activated by the

[Run]

,

[Run DUT]

menu option. This run mode is to work with the

molbox and a DUT Definition, but without a Test Definition (see Section 7.4).

4.

Run Test

- Activated by the

[Run]

,

[Run Test]

menu option. This run mode is to run a Test

Definition on a DUT (see Section 7.2).

«
...
42
43
44
45
46
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

Бренд: Model Technology Страницы: 37

Бренд: COMPRO Страницы: 36

PlateRunner P24 Processor

Бренд: Xante Страницы: 6

Бренд: Agilent Technologies Страницы: 9

Бренд: Promise Technology Страницы: 84

Бренд: Remote Reality Страницы: 61

Portal Server ETV v4.2

Бренд: VBrick Systems Страницы: 64

Application Accelerator RAID Edition

Бренд: Intel Страницы: 85

Бренд: THOMSON Страницы: 22

25385 - Capture NX - Mac

Бренд: Nikon Страницы: 268

22505-051400-9000 - AutoCAD Electrical 2008

Бренд: Autodesk Страницы: 1304

Бренд: pagertec Страницы: 16

Phone Link Handbook

Бренд: Palm Страницы: 22

DirectRoute 3.0

Бренд: Magellan Страницы: 108

Windows BLL Generator

Бренд: Lasergraphics Страницы: 68

Бренд: Fellowes Страницы: 170

SEAL-IT SEAL-IT 100

Бренд: Velocity Страницы: 38

Бренд: Canon Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды