DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя | Manualshive

Страница: 73 / 226

background image

COMPASS



for molbox™ User’s Manual

Page 59

© 1998-2003

DH Instruments, Inc

.

7.2.2.1

MANUAL ENTRY DATA ACQUISITION

When the reference or any portion of the required DUT data requires manual entry,
the

<Manual Entry>

window displays

to allow the necessary data entry. A unit

of measure appears next to each entry field. It is critical that all entries be made
in the specified unit of measure. Failure to due so will result in erroneous data.
This feature is functionally equivalent to clicking the

<Enter Flow Data>

icon on

the

<Control Toolbar>

(see Section 6.6.9). Manual entry of pressure and

temperature data for density correction DUTs (see Section

8.5.3

) can be streamlined

by using the appropriate

[Tools]

,

[Options]

,

[Run Test]

tab selection (see Section 11.6).

Figure 34.

<Manual DUT Data Entry>

Panel

7.2.3 TEST

CONCLUSION

After run test is complete (see Section 7.2.2), test conclusion begins. Other than the repeat
point option, there are two main steps to the test conclusion.

•

Test Notes:

The

<Test Notes>

pop-up appears to allow the user to enter notes

concerning the test run that has just completed. The notes are included in the Data File
and can be used in reports. In multi-cycle tests, only one display for the test notes occurs.
The test notes step can be skipped by selection in the

[Tools]

,

[Options]

,

[End Test]

tab

(see Section 11.7).

•

Test Complete Screen:

If the auto generate report option is selected on the

[Tools]

,

[Options]

,

[End Test]

tab (see Section 11.7), the current report template is used to

generate a report with the test Data File. Regardless of this selection, the

<Test

Complete>

screen displays with the name and path of the test Data File and offers

various post test options. Operation always returns to the

<Test Complete>

screen until

<Exit Test>

has been selected.

Table 14 lists the

<Test Complete>

options.

Figure 35.

<Test Complete>

Panel

«
...
71
72
73
74
75
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

Бренд: NEC Страницы: 4

Portastudio iPad Application

Бренд: Tascam Страницы: 5

Бренд: Omron Страницы: 4

Бренд: Kenwood Страницы: 21

Бренд: Kenwood Страницы: 40

Бренд: Kenwood Страницы: 52

Бренд: Kenwood Страницы: 68

Бренд: Vonamic Страницы: 31

VB Directory System

Бренд: VBrick Systems Страницы: 21

StreamPlayer v4.4

Бренд: VBrick Systems Страницы: 32

Бренд: Adaptec Страницы: 45

ANTI-VIRUS FOR MICROSOFT EXCHANGE 9.00

Бренд: F-SECURE Страницы: 174

ZENWORKS ENDPOINT SECURITY MANAGEMENT 3.5

Бренд: Novell Страницы: 76

Бренд: McAfee Страницы: 315

Бренд: Asus Страницы: 114

Бренд: Asus Страницы: 154

Бренд: Asus Страницы: 72

Бренд: Asus Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды