DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя | Manualshive

Страница: 59 / 226

background image

COMPASS



for molbox™ User’s Manual

Page 45

© 1998-2003

DH Instruments, Inc

.

LABEL

DESCRIPTION

Gas

Active molbox calibration gas. In

[Run molbox]

mode, this value can be changed

using the flow conditions toolbar icon (see Section 6.6.5). In all other run modes, the active
DUT determines the calibration gas. In this case, the value cannot be changed.

Stability Setting

Active Ready/Not Ready stability criterion in the molbox. In

[Run Test]

mode, this

value is fixed by the Test Definition in use. In all other run modes, the stability setting
can be changed using the flow conditions toolbar icon (see Section 6.6.5). See the
molbox Operation and Maintenance Manual, Ready/Not Ready Section, for additional
information.

molbloc

The serial number and molbox channel of the active molbloc. The molbloc channel
displays only when a two channel molbox is the active reference.

6.7.3

DUT OUTPUT RUN SCREEN

The

<DUT Output>

run screen provides a real time update of all relevant DUT output information.

Use this display to view raw output information directly from the DUT. Do not confuse this
run screen with the DUT Definition display. The DUT Definition display merely displays the
current DUT Definition in the DUT Definition Editor. Table 11 describes all of the fields on the

<DUT Output>

run screen.

Figure 23.

<DUT Output>

Run Screen

Table 11.

<DUT Output>

Run Screen Fields

LABEL

DESCRIPTION

Flow

The top of the

<DUT Output>

run screen displays the flow measured by the DUT in

the current DUT flow units. The value is updated each time the necessary output
information is returned from the DUT. If the DUT is manual entry, this field is updated
only when the user enters new output information.

Output

Raw DUT output. The displayed value is always in the output unit setup in the DUT record.

Pressure

DUT gas pressure for DUTs that specify a density correction. If no density correction
is set up, the pressure field is N/A (see Section 8.5.3). When specified, the Pressure
Device in the System Configuration is the source of this pressure value (see Section 10.2).
Otherwise the pressure displayed is a default value or the last value manually entered
(see Section 11.6).

Temperature

DUT gas temperature for DUTs that specify a density correction. If no density correction
is set up, the temperature field is N/A (see Section 8.5.3). When specified, the
Temperature Device in the System Configuration is the source of this temperature
value (see Section 10.2). Otherwise the temperature displayed is a default value or
the last temperature manually entered (see Section 11.6).

«
...
57
58
59
60
61
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

CORPORATE SUITE

Бренд: KAPERSKY Страницы: 36

Network Shutdown Module V3

Бренд: Eaton Страницы: 65

Бренд: Sanford Страницы: 122

WS02-NCTC1-E - 07-2001

Бренд: Omron Страницы: 116

MetaFrame MetaFrame Presentation Server

Бренд: Citrix Страницы: 97

Бренд: Steinberg Страницы: 1

Бренд: Lowrance Страницы: 48

POLICY MANAGER PROXY -

Бренд: F-SECURE Страницы: 43

Бренд: FieldServer Страницы: 10

Ellisimo Gold II

Бренд: Baby Lock Страницы: 50

EDIRECTORY 8.8 SP1

Бренд: Novell Страницы: 150

Бренд: Accordiva Страницы: 31

CLX 3160FN - Color Laser - All-in-One

Бренд: Samsung Страницы: 36

PEG-N610C gMovie v1.3

Бренд: Infinity Softworks Страницы: 29

Gold Corporate 5

Бренд: LapLink Страницы: 166

DEEP FREEZE ENTERPRISE

Бренд: FARONICS Страницы: 6

SCX 5530FN - Multifunction...

Бренд: Samsung Страницы: 35

SmartOffice Mobile

Бренд: Palm Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды