DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 175

Страница: 175 / 226

COMPASS



for molbox™ User’s Manual

Page 161

DH Instruments, Inc

FEATURE

DESCRIPTION

K Factor to N2

(numeric entry field)

The gas conversion factor from the process gas to N2.

K Factor to surrogate

(numeric entry field)

The gas conversion factor from the process gas to the selected surrogate gas.

Surrogate name

(text entry field)

A full text name of the surrogate gas.

Record

(action button)

Record the changes to the displayed process gas information. When

<Record>

pressed, a new gas can be added or edited prior to saving the file. Failure to press
record will undo all changes made.

Delete

(action button)

Remove the current process gas from the DUT manufacturer. The

<Gas information

for current manufacturer>

selection determines which gas will be removed.

Save File

(action button)

Permanently saves all changes recorded in the

Process Gas Editor

. If this button is

not pressed prior to closing the editor, none of the updates will be stored.

Содержание COMPASS FOR MOLBOX



































































































































































































































Результаты поиска

Содержание COMPASS FOR MOLBOX

Отзывы:

Похожие инструкции для COMPASS FOR MOLBOX

Бренды по названию

Популярные бренды

DH Instruments COMPASS FOR MOLBOX, Руководство пользователя

Результаты поиска

Содержание COMPASS FOR MOLBOX

Отзывы:

Похожие инструкции для COMPASS FOR MOLBOX

Бренды по названию

Популярные бренды