DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 17

Страница: 17 / 226

COMPASS



for molbox™ User’s Manual

Page 3

DH Instruments, Inc

2.1 OVERVIEW

This section explains how to install

COMPASS for molbox

on your computer.

2.2 SYSTEM

REQUIREMENTS

COMPASS for molbox

is an application designed for Windows 32 bit operating systems. This includes

Windows 95, 98 and NT. Although any computer running one of these operating systems has the basic
requirements to run

COMPASS

, it is recommended that the following minimum configuration be used:

•

Windows 95, 98, or NT

•

200 MHz, Pentium processor

•

32 MB RAM

•

10 MB free hard disk space

2.3

INSTALLING COMPASS FOR molbox

Insert the

COMPASS for molbox

CD into the CD drive. If the auto run feature is enabled on the

PC, the setup application runs automatically.

If the setup program does not run after 10 seconds, press the Windows

[Start]

button and select

[Run]

In the Run dialog box, type

d:\setup

f:\setup

, depending on the drive letter of the CD drive of the

installation disk. Select

COMPASS for molbox

from the list of applications and follow the

installation prompts to install the program.

2.3.1.1.1.1 OR

Insert the

COMPASS for molbox

CD into the CD drive.

Use the

Add/Remove Programs

feature in the Windows

Control Panel.

Press the Windows

[Start]

button and select

[Settings]

followed by

[Control Panel]

Double-click the

[Add/Remove Programs]

icon and click the

[Install]

button. Follow the prompts

to install

COMPASS

. Select

COMPASS for molbox

from the list of applications and follow the

installation prompts to install the program.

2.3.2

UPGRADING FROM VERSIONS LOWER THAN 4.00

During the installation process, choose the directory of any existing version of

COMPASS

automatically upgrade the program. When the new version runs for the first time, the

COMPASS

file Upgrade Wizard (see Section 2.3.3) will run to facilitate the conversion of

Содержание COMPASS FOR MOLBOX



































































































































































































































Результаты поиска

Содержание COMPASS FOR MOLBOX

Отзывы:

Похожие инструкции для COMPASS FOR MOLBOX

Бренды по названию

Популярные бренды

DH Instruments COMPASS FOR MOLBOX, Руководство пользователя

Результаты поиска

Содержание COMPASS FOR MOLBOX

Отзывы:

Похожие инструкции для COMPASS FOR MOLBOX

Бренды по названию

Популярные бренды