DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 226

background image

COMPASS



for molbox™ User’s Manual

Page 111

© 1998-2003

DH Instruments, Inc

.

10.3.5 [POWER

SUPPLY]

TAB

The

[Setup]

,

[Hardware]

,

[Power Supply]

tab is used to manage the power supply

Definitions that are included in the System Configuration

<Set point power supply>

drop

down list (see Section 10.2).

The

[Power Supply]

tab provides a list of the power supplies available, displays complete

information on the selected power supply, allows the power supply to be edited or a new
power supply to be created.

To select a power supply Hardware Definition to view, single click on the power supply name
and serial number in the

<List>

display panel (upper left-hand corner). To edit an existing

power supply, double click on the power supply listing or click on the

<Edit>

toolbar function

with the desired power supply highlighted. Double clicking the power supply listing, clicking
on the

<Edit>

toolbar function or clicking on the

<New>

new toolbar function causes the

<Edit Reference Device>

or

<Add New Reference Device>

pop-up to appear. These pop-ups

are identical but differentiated by name to make it clear which task is currently being performed.

The

<Edit Power Supply>

or

<Add Power Supply>

pop-ups allow a reference device to be

set up from scratch or edited from an existing one.

The purpose of the power supply Definition fields and settings as well as instructions on how
to use them are provided in Table 38. When creating a new Definition, all the fields come
up blank. When editing an existing Definition, the fields come up populated with the
information on that device. When editing is complete, click

<OK>

to save changes.

The molbox MFC control option acts as a [Power Supply], however, it does not need to be

set up under the [Power Supply] tab. In the System Configuration, when a molbox is

selected as the <Flow Reference>, <Reference molbox> is automatically included as a
choice in the <Setpoint Power Supply> field (see Section 10.2).

Figure 63.

Hardware Definition,

[Power Supply]

Tab

«
...
123
124
125
126
127
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

PowerShot SX1 IS

Бренд: Canon Страницы: 48

Бренд: Canon Страницы: 2

Analog Factory S.E.

Бренд: Arturia Страницы: 31

DEEP FREEZER PROFESSIONAL

Бренд: FARONICS Страницы: 31

Secure Perfect 6.1.1

Бренд: GE Страницы: 269

HyperMedia Center

Бренд: Genius Страницы: 12

Бренд: Better Light Страницы: 99

VANTAGE CNM 2.0 -

Бренд: ZyXEL Communications Страницы: 346

PowerVideo Plus

Бренд: EverFocus Страницы: 80

Бренд: Nikon Страницы: 12

256B1-05A761-1301 - AutoCAD Revit Structure Suite 2010

Бренд: Autodesk Страницы: 1638

Бренд: Genius Страницы: 3

Бренд: Genius Страницы: 2

VIDEOCAM SLIM USB2

Бренд: Genius Страницы: 4

Бренд: Genius Страницы: 11

Бренд: QMS Страницы: 50

MEDIASTUDIO PRO 6.0

Бренд: Ulead Страницы: 360

ANTI-VIRUS 5.0 - FOR SAMBA SERVERS

Бренд: KAPERSKY Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды