DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 223 | Manualshive

Страница: 223 / 226

background image

COMPASS



for molbox™ User’s Manual

Page 209

© 1998-2003

DH Instruments, Inc

.

Stability Limit

A limit expressed in units of flow per second (e.g., sccm/second). The stability limit is
used as the molbox

Ready/Not Ready

criterion

Ready (

<*>

)

if rate is less than stability

limit,

Not Ready

(

<

↑

>

or

<

↓

>

) if rate is greater than stability limit. See also

Rate

.

Surrogate Gas

A gas whose behavior, from the standpoint of a device under test (DUT), is similar to
the process gas for which the device is to be characterized and used. A surrogate gas
is often used in calibration and testing when the process gas cannot be used for safety
or cost reasons. A DUT gas conversion factor (“K” factor) is used to convert from the
surrogate gas to the process gas.

System
Configuration

A listing of the specific hardware items that

COMPASS

uses by default to perform

various data acquisition and control functions. The System Configuration is made up
of individual Hardware Definitions.

Tare

“Zeroing” of the molbox pressure transducers at the upstream or downstream pressure
to eliminate the zero error in the measurement of the differential pressure across a
molbloc. molbox1 and molbox RFM have automated taring routines and

COMPASS

can cause these to execute during a test. See the molbox Operation and Maintenance
Manual,

[Tare]

Section.

Test Definition

A database record which defines all the aspects of a test procedure that

COMPASS

can run on a DUT. Test Definitions are associated with DUTs and control the test
procedure when a test is run.

Test Gas

The gas flowing through the molbloc that is being used to run the test or calibration.
The test gas, from the standpoint of the device under test, could be a surrogate gas or
the process gas.

Tolerance

Same as DUT tolerance.

Upstream

Location of point A relative to point B in a flow system in which point A is at a different
location in the reverse direction of the flow. For example, the upstream molbloc
pressure port is upstream relative to the downstream pressure port because it is at a
different location from the downstream port in the opposite direction of the flow.

Volume Flow Units

Units of measure of volume flow (sometimes called “actual flow”). Do not confuse
volume flow units with volumetrically based mass flow units. See the molbox Operation
and Maintenance Manual,

[Unit]

Section, for an extensive discussion of flow units of

measure.

«
...
221
222
223
224
225
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

Jetstream CPX-1000

Бренд: Paradyne Страницы: 93

TRANSCEND EM/NT 6.3

Бренд: 3Com Страницы: 39

Бренд: Campbell Страницы: 133

BACKUP AND RECOVERY 10 ADVANCED SERVER VIRTUAL EDITION - COMMAND LINE REFERENCE UPDATE 3

Бренд: ACRONIS Страницы: 54

NeatWorks For Mac

Бренд: NeatWorks Страницы: 33

Бренд: LinPlug Страницы: 46

Бренд: M-Audio Страницы: 15

Ramp Preview Controller

Бренд: ARRI Страницы: 46

Бренд: Measurement Computing Страницы: 109

MOBILE SECURITY FOR S60 -

Бренд: F-SECURE Страницы: 33

Бренд: GRASS VALLEY Страницы: 8

K2 FCP CONNECT -

Бренд: GRASS VALLEY Страницы: 19

Бренд: UNIBLUE Страницы: 3

Бренд: Sun Microsystems Страницы: 24

ENTERPRISE LINUX 4.5.0 -

Бренд: Red Hat Страницы: 434

256B1-05A761-1301 - AutoCAD Revit Structure Suite 2010

Бренд: Autodesk Страницы: 1638

Бренд: Bay Networks Страницы: 130

Бренд: AAS Страницы: 177

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды