DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 226

background image

COMPASS



for molbox™ User’s Manual

© 1998-2003

DH Instruments, Inc

.

Page 88

9.5.4 [SEQUENCE]

TAB

The Test Definition

[Sequence]

tab is used to specify details of how the test points of a test

will execute (see Section 7.1). This includes defining dwell and data reading parameters as
well as the number of times to run the test (number of cycles). Note that the order of the
fields of the sequence tab follows the order of execution of the different steps of each flow
point when a test is actually run.

The purpose of the

[Sequence]

tab’s fields and settings as well as instructions on how to use

them are provided in Table 27.

Figure 50.

Test Definition Editor,

[Sequence]

Tab

Table 27.

Test Definition Editor,

[Sequence]

Tab Fields

FEATURE

DESCRIPTION

Stability

Test and Hold

Time

(required

numeric entry

fields)

Defines the stability limit to be used to determine a ready condition in the molbox
after a target flow is set. Generally, this value is set about 10 times smaller than
the DUT tolerance/second (see the molbox Operation and Maintenance Manual,
Ready/Not Ready Section). The associated time entry field is the Stability Hold time.
For

COMPASS to

consider that the stability test has been met and test

execution can continue, the ready condition (flow inside stability limit) must be
present and uninterrupted for the Stability Hold time. If during the Stability Hold
Time, the molbox outputs a not ready signal, the hold time will start over after the next
ready output is received. This process continues until either the stability test is
passed or the

<Stability Time-Out>

occurs.

Depending on the configuration of the test system and the performance of the
device controlling the flow, the flow may stabilize within the stability test and a
ready condition may occur momentarily before the flow has truly stabilized.
The Stability Hold Time can be used to assure that the flow remains stable for a
certain amount of time before the stability test is considered to have been met
and test execution continues.

Stability Time-

out

(required

numeric entry

field)

The maximum amount of time that the

<Stability Test>

process may consume.

If the stability test and Stability Hold Time have not been satisfied within the

<Stability Time-Out>

an indicating character is recorded in the Data File and on

the Test Grid and test execution continues. The stability time out is used to
assure that a test will not hang indefinitely if the stability test cannot be met at a
flow point.

«
...
100
101
102
103
104
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

FLEXXPECT-PHARMA

Бренд: Omron Страницы: 2

Бренд: ICP Страницы: 16

NI Spectral Measurements Toolkit

Бренд: National Instruments Страницы: 35

ForeSight 6100 Element Management System

Бренд: Patton electronics Страницы: 70

Бренд: MMSOFT Design Страницы: 85

Бренд: Crestron Страницы: 12

Diabetes Management Software v2.2

Бренд: OneTouch Страницы: 13

Бренд: Draytek Страницы: 60

POWER WAVE 405M

Бренд: Lincoln Electric Страницы: 42

Бренд: FieldServer Страницы: 48

850DP - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 70

REGISTRYBOOSTER 2010 - V1

Бренд: UNIBLUE Страницы: 11

Storage Software PathManager

Бренд: NEC Страницы: 65

GPS navigation software for Audiovox NVX200

Бренд: Jensen Страницы: 86

Бренд: Mackie Страницы: 26

Бренд: HP Страницы: 283

Intellisync 9.2

Бренд: Nokia Страницы: 48

Бренд: Nokia Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды