DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя | Manualshive

Страница: 171 / 226

background image

COMPASS



for molbox™ User’s Manual

Page 157

© 1998-2003

DH Instruments, Inc

.

Table 56. <Flow Unit Converter>

Panel Fields

FEATURE

DESCRIPTION

Current

Pressure

(numeric entry

field/drop down

list box)

The numeric pressure value in the units that will be converted.

Calculated

Pressure

(display field/

drop down list

box)

The converted pressure value in the selected pressure units.

Current

Temperature

(numeric entry

field/drop down

list box)

The numeric temperature value in the units that will be converted.

Calculated

Temperature

(display field/

drop down list

box)

The converted temperature value in the selected temperature units.

Current Gas

(drop down list

box)

The gas for which the flow unit conversion will take place. The complete list of

COMPASS

supported calibration gases is available for selection.

Pressure

(optional

numeric entry

field)

Ignore this field if you are not converting a volume or actual flow unit.

Volume or actual flow unit conversions require instantaneous pressure values. If an actual
flow unit is selected enter the pressure in Pascal into this field. If necessary use the pressure
unit converter to determine the actual pressure in Pascal.

Temperature

(optional

numeric entry

field)

Ignore this field if you are not converting a volume or actual flow unit.

Volume or actual flow unit conversions require instantaneous temperature values. If an
actual flow unit is selected enter the temperature in Kelvin (K) into this field. If necessary use
the temperature unit converter to determine the actual temperature in K.

Current Flow

(numeric entry

field/drop down

list box)

Enter the numeric value of the flow in the units that will be converted. The drop down list of
flow units contains the complete list of units defined by the

Flow Unit Editor

(see Section

14.2).

Since actual flow units require a density correction, pressure and temperature values must
also be specified if an actual flow unit is selected.

Calculated

Flow

(display field/

drop down list

box)

The converted flow based on the supporting flow unit information. If the selected flow unit is
an actual flow unit, pressure and temperature data must be included.

«
...
169
170
171
172
173
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

70 MC - ZR70MC MiniDV Digital Camcorder

Бренд: Canon Страницы: 57

Portastudio iPad Application

Бренд: Tascam Страницы: 5

RESTORATION SUITE

Бренд: TC Electronic Страницы: 31

Veriteq viewLinc 4.0

Бренд: Vaisala Страницы: 168

Бренд: Arturia Страницы: 125

FLEX - DEVELOPING COMPONENTS AND THEMES

Бренд: MACROMEDIA Страницы: 82

LIVE CYCLE 7.2 - INSTALLING AND CONFIGURING LIVECYCLE FOR JBOSS

Бренд: Adobe Страницы: 90

Бренд: Campbell Страницы: 250

ThinkCentre A58

Бренд: Lenovo Страницы: 2

Бренд: Pioneer Страницы: 11

Sound Editor ver. 2.10

Бренд: Yamaha Страницы: 11

Бренд: Yamaha Страницы: 11

Бренд: Yamaha Страницы: 17

FIRESTATION MLAN PATCHBAY

Бренд: Yamaha Страницы: 17

S03 voice editor

Бренд: Yamaha Страницы: 20

S08 Voice Editor

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 28

Бренд: Yamaha Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды