DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 149

Страница: 149 / 226

COMPASS



for molbox™ User’s Manual

Page 135

DH Instruments, Inc

Table 50. [Options], [Display]

Tab Fields

FEATURE

DESCRIPTION

Run molbox

(drop down list box)

Select the default

[Run molbox]

run mode display from the list. Realize that

only the

<molbox Output>

and the

<Averaging>

run screens are available

for display in this run mode. Run screens other than these will not display
regardless of the display mode selected.

Run DUT

(drop down list box)

Select the default

[Run DUT]

run mode display from the list. Realize that only

the

<molbox Output>

<DUT Output>

<Comparison Screen>

and the

<Averaging>

run screens are available for display in this run mode. Run

screens other than these will not display regardless of the display mode
selected.

Run Test

(drop down list box)

Select the default

[Run Test]

run mode display from the list. All run screens

with the exception of the

<Averaging>

screen are available in this run mode.

Any display selected that contains this window will not arrange as expected.

Remove Display Selection

(drop down list box)

Use this feature to remove unwanted custom displays. Select the display
from the list then press the

<->

button.

Содержание COMPASS FOR MOLBOX



































































































































































































































Результаты поиска

Содержание COMPASS FOR MOLBOX

Отзывы:

Похожие инструкции для COMPASS FOR MOLBOX

Бренды по названию

Популярные бренды

DH Instruments COMPASS FOR MOLBOX, Руководство пользователя

Результаты поиска

Содержание COMPASS FOR MOLBOX

Отзывы:

Похожие инструкции для COMPASS FOR MOLBOX

Бренды по названию

Популярные бренды