DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 226

background image

COMPASS



for molbox™ User’s Manual

© 1998-2003

DH Instruments, Inc

.

Page 122

Figure 69.

[Options], [molbox]

Tab

Table 42. [Options], [molbox]

Tab Selections

FEATURE

DESCRIPTION

Allow selection

of gases for

which the

molbloc is not

calibrated

(check box)

Though any molbox supported gas can always be selected on the molbox, the
molbloc may or may not have been calibrated with that gas. The molbox can
determine whether the molbloc has been calibrated with a gas or not.

By default this field is checked to allow a test to proceed with any molbox supported
gas regardless of whether the molbloc has been calibrated with that gas. When
this field is not checked, a warning message is generated when a gas with which
the molbloc was not specifically calibrated is selected.

Enable MFC

switchbox

(check box)

By default this field is checked to provide selections for the MFC switchbox when a
molbox1 that supports the switchbox is the flow reference in

[Run DUT]

and

[Run Test]

run modes. If the optional MFC switchbox was not purchased with the

molbox or will not be used, uncheck this function to avoid the extra prompts that
occur during test initialization.

Prompt for MFC-

CB channel

(check box)

Check this option when the channel used on an MFC-CB may differ from test to
test. A message displays during test initialization that allows the MFC-CB channel
to be selected for controlling or measuring an MFC. If an MFC-CB is not selected
for use in the

Hardware Configuration

, this option is not ignored.

Do not check this option if you wish to use the active MFC-CB channel for
controlling and measuring MFCs.

Always use

molbox RFM

microrange

(check box)

This option is on by default to always activate the molbox RFM microrange (when
available) as part of the test initialization. This is typically the desired use of the
molbox RFM. Uncheck the field to use the current microrange state when using the
molbox RFM. See the molbox RFM Operation and Maintenance Manual for additional
information on the microrange.

Use active

molbox channel

by default

(check box)

Check this option to use the currently active molbox1-95 channel when initializing
the molbox. Checking this option speeds up the initialization time by preventing the
need to read both molbox channels. For example, if the molbox1-95 is setup to use
channel B,

COMPASS

assumes channel B will be used for testing. This feature

has no function when a molbox1 or molbox RFM is used as the flow reference device.

«
...
134
135
136
137
138
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

COOL 3D-PLUG-IN MADNESS II

Бренд: Ulead Страницы: 10

WiFi-Doc Client for iOS

Бренд: Mitsubishi Страницы: 10

SNAP DEPLOY 2.0 -

Бренд: ACRONIS Страницы: 68

Бренд: Sanyo Страницы: 132

Бренд: Ulead Страницы: 218

POWER WAVE 405M

Бренд: Lincoln Electric Страницы: 42

3CR15600 - Enterprise Management Suite

Бренд: 3Com Страницы: 218

AURORA EDIT - INSTALLATION V7.1

Бренд: GRASS VALLEY Страницы: 152

AUTOCAD P AND ID 2010

Бренд: Autodesk Страницы: 4

657B1-000110-S001 - Maya - Mac

Бренд: Autodesk Страницы: 5

Бренд: Bay Networks Страницы: 130

Бренд: QMS Страницы: 50

141670 - DS 330 Digital Voice Recorder

Бренд: Olympus Страницы: 72

Guitar Tone Processor GTR Solo

Бренд: Waves Страницы: 29

Бренд: Acer Страницы: 4

SyncMaster T23A950

Бренд: Samsung Страницы: 46

Бренд: Canon Страницы: 28

Бренд: Lenovo Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды