DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 226

background image

COMPASS



for molbox™ User’s Manual

© 1998-2003

DH Instruments, Inc

.

Page 150

represent the physical connection of the device and an RS-232 port on the host computer or
the currently configured reference device.

Use the

<Ref Com2>

selection found at the end of the

<COM Port>

drop down list to access

the currently configured reference COM2 port rather than a standard communications port on
the host PC.

<Ref Com2>

is usually COM2 of a molbox flow reference. If the reference

device does not have a valid COM2,

COMPASS

will generate an error when trying to access

the port. No special command setup is required to use the

<Ref Com2>

option. Select this

option just as any other COM port selection,

COMPASS

will set up the reference device

COM2 port and modify the commands as needed to send and receive commands using
this interface.

Figure 87. <RS232 Settings>

Panel

13.4 IEEE-488

INTERFACE

IEEE-488, also known as GPIB (General Purpose Interface Bus), is a popular instrument
interface protocol. This interface allows a single IEEE-488 controller card to simultaneously interface with
up to 15 instruments. Each instrument must be set to an independent IEEE-488 address from 1 to 30.
The controller card also has an address that is used when multiple IEEE-488 cards are installed in the
PC. However, this is a rare case.

To use IEEE-488 with

COMPASS

, use the

[Setup][System], <IEEE-488 Card>

option to select the

IEEE-488 card installed in your PC (see Section 10.2). When this selection is made, no other card
related selections are required, only the instrument IEEE-488 address must be specified. Refer to the
instrument documentation for more information on how to determine the instrument IEEE-488 address.

13.5 DEVICENET

INTERFACE

COMPASS

supports National Instruments and SST DeviceNet interface cards. Select the card to use

with the

[Setup][System], [DeviceNet Card]

option (see Section 10.2). The command protocol as

outlined by the ODVA DeviceNet Specification is used by

COMPASS

to read and set flow. For this

reason, a remote command setup is not necessary. Output units and other settings within the device are
not changed. The DUT Definition must include the correct output range and unit information just like any
other DUT. The DeviceNet device MacID and baudrate are the only selections required to setup the
DeviceNet interface of a DUT.

13.6 [TOOLS], [REMOTE COMMUNICATIONS]

[Tools]

,

[Remote Communications]

provides a simple means of sending individual command strings to

remote devices and receiving and displaying the response. This tool can be used for discreet remote
device communication and communications testing. Use this tool to familiarize yourself with the device’s
communications, for troubleshooting communications problems and determining the appropriate

«
...
162
163
164
165
166
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

Бренд: TANDBERG Страницы: 66

Content Server None

Бренд: TANDBERG Страницы: 14

UNIVERSAL CONTROL 1.1 SVN 2108

Бренд: PRESONUS Страницы: 1

Modero ViewPoint MVP-5100

Бренд: AMX Страницы: 190

BMP5 Direct SDK

Бренд: Campbell Страницы: 32

DEEP FREEZE - INTEGRATING WITH ALTIRIS...

Бренд: FARONICS Страницы: 22

SNAP DEPLOY 2.0 -

Бренд: ACRONIS Страницы: 68

Бренд: Brother Страницы: 22

Бренд: Brother Страницы: 115

Бренд: Ulead Страницы: 58

Бренд: DeLorme Страницы: 29

Бренд: Intel Страницы: 30

Бренд: IBM Страницы: 220

Бренд: Panasonic Страницы: 102

Бренд: Sun Microsystems Страницы: 32

VS4-ENT-PL-A - vSphere Enterprise Plus

Бренд: VMware Страницы: 276

ThinkCentre A55

Бренд: Lenovo Страницы: 210

ThinkCentre A57

Бренд: Lenovo Страницы: 788

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды