DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя

Страница: 138 / 226

COMPASS



for molbox™ User’s Manual

DH Instruments, Inc

Page 124

FEATURE

DESCRIPTION

Display mass

flow unit

(drop down list

box)

COMPASS

always calculates and displays the final molbox flow in the selected

DUT Definition flow unit of measure in

COMPASS

run screens. However, the front

panel of the molbox always displays in the fixed

mass

flow unit selected by this

option. This flow unit will display in the

<molbox Output>

run screen during

[Run

DUT]

and

[Run Test]

run modes (see Section 6.7). The molbox display flow units

are limited because the

COMPASS

always reads and uses true mass flow units.

11.3 [GRID]

TAB

The

[Tools]

[Options]

[Grid]

tab is used to customize the Data Grid run screen that is available while

running tests (see Section

6.7.5

). The grid can be customized to display only desired columns of data,

suppressing other columns, and to put the columns in a desired order. Any test data item logged in the
Data File can be included in any column of the Data Grid run screen by using the correct combination of
features (see Section 18.4.1).

Instructions on the operation of the

[Grid]

tab are provided in Table

. When the grid is set up as

desired, click

<OK>

to save changes.

All data is logged to the Data File in the same format regardless of the columns of data selected for

display using the [Grid] tab. The grid setup is provided for customization of the <Data Grid>

run

screen only (see Section 6.7.5). Use the [View Data File] option to view all columns of test data
(see Section 12.2).

Multiple grid display items can be selected in two ways: a) hold down the SHIFT key and use the UP

and/or DOWN arrow keys to make multiple contiguous selections; b) hold down the CTRL key and us the

mouse to make multiple non contiguous selections. Add or remove the selections by using the
appropriate shift button.

Sort the <Columns in grid> display by selecting an item then using the UP or DOWN arrow keys while

holding the CTRL button.

Figure 70.

[Options], [Grid]

Tab

Содержание COMPASS FOR MOLBOX



































































































































































































































Результаты поиска

Содержание COMPASS FOR MOLBOX

Отзывы:

Похожие инструкции для COMPASS FOR MOLBOX

Бренды по названию

Популярные бренды

DH Instruments COMPASS FOR MOLBOX, Руководство пользователя

Результаты поиска

Содержание COMPASS FOR MOLBOX

Отзывы:

Похожие инструкции для COMPASS FOR MOLBOX

Бренды по названию

Популярные бренды