DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 226

background image

COMPASS



for molbox™ User’s Manual

© 1998-2003

DH Instruments, Inc

.

Page 34

6.6.1 CHANGE/RELOAD

molbloc

This feature is represented by the toolbar icon:

When using molbox1 as a reference, this tool displays a pop-up panel allowing a new molbloc
channel to be selected:

A, B or A+B

. If the selected channel does not contain a valid molbloc,

an error message displays and the molbox flow displays

<Error>

until the molbloc channel is

changed back to a valid channel. For all other molbox references, this feature reloads the
current molbloc channel. This feature is not available when the reference is not a molbox.

6.6.2 TARE

molbox

The tare molbox feature is represented by the toolbar icon:

See the molbox Operation and Maintenance Manual, Tare Section, for complete information
and recommendations on molbox pressure transducer taring.

This function executes the molbox tare function. When pressed, a message displays allowing
the selection of the tare pressure: upstream or downstream. After this selection, the reference
molbox’s internal valves are actuated to set up the tare configuration. The current pressure
measured by the molbox pressure transducers is displayed on the

<Tare molbox>

panel.

When the pressure is stable, the circular ready indicator will change to green and the tare
button is enabled. Press

<Tare>

to activate the current value. The

<Status Bar>

displays

<Tare Complete>

after the tare is set. The

<Tare molbox>

panel does not automatically

close after the tare function has been executed. This allows the tare to be repeated as many
times as desired. Use the close control box or the

<Continue>

button to complete the tare

process and activate the new tare values.

See Table 4 for information on each of the tare molbox panel fields.

Figure 14.

<Tare molbox>

Panel

«
...
46
47
48
49
50
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

RAPTOR 2100 FPS - RAPTOR DRIVERS FOR HP-UX INSTALLATION AND

Бренд: Tech Source Страницы: 36

Бренд: NETGEAR Страницы: 2

Бренд: Juniper Страницы: 772

COLDFUSION 5-DEVELOPING

Бренд: MACROMEDIA Страницы: 438

Бренд: Euphonix Страницы: 8

Бренд: DigiDesign Страницы: 39

Бренд: DeLorme Страницы: 34

POLICY MANAGER PROXY 2.0 -

Бренд: F-SECURE Страницы: 24

Бренд: ACT Страницы: 124

Бренд: UNIBLUE Страницы: 3

Бренд: VERITEQ Страницы: 112

Бренд: FieldServer Страницы: 10

Бренд: Genius Страницы: 3

Бренд: Genius Страницы: 2

VIDEOCAM SLIM USB2

Бренд: Genius Страницы: 4

Бренд: Genius Страницы: 11

Бренд: DigiDesign Страницы: 886

DEEP FREEZE - SMS INTEGRATION 8-2006

Бренд: FARONICS Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды