DH Instruments COMPASS FOR MOLBOX Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 226

background image

COMPASS



for molbox™ User’s Manual

Page 9

© 1998-2003

DH Instruments, Inc

.

4

4

.

.

Q

Q

U

U

I

I

C

C

K

K

T

T

I

I

P

P

S

S

4.1

HOW DO I?

Set up and run a test?

Create a Test Definition to define the test procedure (see Section 9).

Create a DUT Definition to define a device under test (see Section 8).

Configure the test hardware to be used to run the test (see Section 10).

Run test (see Section 7.2).

Display the flow unit I want on the molbox1 or molbox RFM front panel display
during COMPASS operation?

The various COMPASS run screens, rather than the molbox display, should be used to
obtain molbox output information. COMPASS sets the molbox to fundamental mass

flow units and then performs conversions to the other units and other operating

conditions when required. Do not refer to the molbox display when you are running
COMPASS.

A list of standard mass flow units available for display on the molbox can be selected using the

[Tools], [Options, [molbox],

<Display mass flow units>

units feature (see Section 11.2).

As an alternative, press

[AVERAGE]

,

[DISPLAY]

on the molbox keypad. Select the unit of

measure that you would like displayed on the second (bottom) line of the front panel display.
(Refer to the molbox Operation and Maintenance Manual, DISPLAY Section, for details.)
Keep in mind that

COMPASS

does not transmit pressure and temperature values for

volume or actual flow units to the molbox even if

COMPASS

is making real time measurements.

Therefore, the volume flow units displayed by the molbox and by

COMPASS

will not agree.

Run a test in which the flow at each point is adjusted to a nominal flow value,
for example to the nominal point when calibrating a rotameter?

Specify “jog before dwell” in the Test Definition (see Section 9.5.6). This causes test
execution to pause at each point to allow flow adjustment (jog) prior to taking data at the
point.

Use COMPASS to run tests with a reference other than a DHI molbloc/molbox?

Though

COMPASS

only supports automated operation with

DHI

molbloc/molbox mass

flow references,

COMPASS

can be used to run manual entry tests with any flow reference.

Using the

[Setup]

,

[Hardware]

,

[Reference]

tab, set up a reference selecting

<Other>

as

the

<Manufacturer>

(see Section 10.3.3). A test can then be run in which reference flow

values are entered manually at each point. DUT readings can be automated or not as in
any other test. This feature allows

COMPASS

to be used to standardize flow calibration

procedures and data reporting even with references with which

COMPASS

cannot

interface directly. Entry of reference flow values must be in the flow units that are selected
for display on the molbox. To change these units, go to the

[Tools], [Options], [molbox]

tab and use

<Display mass flow unit>.

«
...
21
22
23
24
25
...
»

Содержание COMPASS FOR MOLBOX



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMPASS FOR MOLBOX

Бренд: Panasonic Страницы: 20

Бренд: Halcro Страницы: 12

and Vantage Pro

Бренд: DAVIS Страницы: 16

Бренд: FARONICS Страницы: 5

Бренд: FARONICS Страницы: 2

DEEP FREEZE ENTERPRISE

Бренд: FARONICS Страницы: 3

ANTI-EXECUTABLE ENTERPRISE

Бренд: FARONICS Страницы: 2

Бренд: Extreme Networks Страницы: 546

ExtremeWare 7.5

Бренд: Extreme Networks Страницы: 2546

Бренд: COMPRO Страницы: 36

SNAP DEPLOY 2.0 -

Бренд: ACRONIS Страницы: 68

Бренд: ARTEX Страницы: 33

Бренд: Extron electronics Страницы: 124

dc5750 - Microtower PC

Бренд: Promise Technology Страницы: 114

ALTIRIS DEPLOYMENT SOLUTION

Бренд: Symantec Страницы: 3

Бренд: GRASS VALLEY Страницы: 174

24108-051462-9000 - AUTOCAD REVIT ARCH STE 08 COMM NEW SLM DVD

Бренд: Autodesk Страницы: 11

057A1-05A111-10MD - AutoCAD LT 2009

Бренд: Autodesk Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды