Dell PowerEdge M620 Скачать руководство пользователя страница 120

Страница: 120 / 368

120

About Your System

MEMTEST lane
failure detected
on

Invalid memory

configuration. A

mismatched DIMM is

installed.

Ensure that the memory

modules are installed in a

valid configuration. See

"System Memory" on

page 171.

Processors

with

different power
rating detected!
System halted

Mismatched processors are

installed.

Ensure that all processors

have the same cache size,

number of cores and logical

processors, and power

ratings, and that they are

properly installed. See

"Processors" on page 243.

Processors

with

different logical
processors
detected!
System halted

CPUs with
different core
sizes detected!
System halted

CPU x installed
with no memory

Memory modules are

required but not installed

in the indicated processor's

memory slots.

Install memory modules for

the processor. See "System

Memory" on page 171.

Unused memory
detected. DIMM's
installed in the
following slot are
not available when
in Mirror or 128-
Bit Advanced ECC
modes: x,x,x

The memory

configuration is not

optimal for mirroring or

Advanced ECC Memory

Mode. Modules in the

specified slot(s) are

unused.

Reconfigure the memory for

Memory Mirroring or

Advanced ECC Memory

Mode, or change the

memory mode to Optimized

in the BIOS setup screen.

See "System Memory" on

page 171.

Table 1-27. Blade Messages

(continued)

Message

Causes

Corrective Actions

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды