Dell PowerEdge M620 Скачать руководство пользователя страница 55

Страница: 55 / 368

About Your System

Mezzanine Cards

PowerEdge M610x Only

PowerEdge M610x supports two mezzanine cards. Mezzanine cards can be

installed in both the slots on the midplane interface card.

NOTE:

PowerEdge M610x is a full-height blade but supports only two mezzanine

cards in the expansion bay. The two mezzanine slots on the M610x system board

(MEZZ2_FAB_B and MEZZ1_FAB_C) are reserved for the mezzanine interface card.

See "Mezzanine Interface Card (PowerEdge M610x Only)" on page 215.

Full-Height Blades

Full-height blades support four mezzanine cards:

• Slot Mezz1_Fabric_C and slot Mezz3_Fabric_C support Fabric C. They

must match the fabric type of the I/O modules installed in I/O module

slots C1 and C2.

• Slot Mezz2_Fabric_B and slot Mezz4_Fabric_B support Fabric B. They

must match the fabric type of the I/O modules installed in I/O module

slots B1 and B2.

Half-Height Blades

Half-height blades support two mezzanine cards:

• Mezzanine card slot C supports Fabric C. This card must match the fabric

type of I/O modules installed in I/O module slots C1 and C2.

• Mezzanine card slot B supports Fabric B. This card must match the fabric

type of I/O modules installed in I/O module slots B1 and B2.

See "I/O Module Mezzanine Cards" on page 217 for more information on

mezzanine cards.
Table 1-13 shows various supported combinations of mezzanine cards and I/O

modules.

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды