Dell PowerEdge M620 Скачать руководство пользователя страница 133

Страница: 133 / 368

About Your System

133

Memory set to
minimum frequency.

The memory frequency

may be intentionally set

lower for power

conservation.

If not an intentional setting,

check any other system

messages for possible causes.

The current memory

configuration may support

only the minimum

frequency.

Ensure that your memory

configuration supports the

higher frequency. See

"System Memory" on

page 171.

Warning! A fatal
error has caused
system reset.
Please check the
event log for
details.

Unspecified error.

Check the system event log

for information about the

error.

Warning! Following
faulty DIMMs are
disabled: DIMM

DIMM

Faulty or improperly

seated memory modules.

See "Troubleshooting Blade

Memory" on page 319.

Warning! No
microcode update
loaded for
processor

Unsupported processor.

Update the BIOS firmware

using the Dell Support

website at

support.dell.com

Warning: The
current memory
configuration is
not validated.
Change it to the
recommended memory
configuration or
press any key to
continue.

There is no memory

configuration error, but

the memory configuration

is not recommended by

Dell.

See "System Memory" on

page 171.

Table 1-27. Blade Messages

(continued)

Message

Causes

Corrective Actions

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды