Dell PowerEdge M620 Скачать руководство пользователя страница 291

Страница: 291 / 368

Installing Enclosure Components

291

Installing a Power Supply Module

Ensure that the power supply module handle is fully open and the power

cable is not plugged into the electrical outlet.

Slide the power supply module into the enclosure. See Figure 4-2.

Rotate the power supply module handle upward until it latches.

Plug a power cable into the power supply module.

Secure the cable to the power supply with the retention clip by fitting the

retention clip over the cable, and fitting the retention clip tether into the

notch in the power supply handle. See Figure 4-1.

Fan Modules

The M1000e enclosure contains nine hot-swappable fan modules. All nine fan

modules must be installed at all times to ensure proper cooling.

Removing a Fan Module

NOTE:

After a fan module is removed from the system, replace it immediately.

Identify the failed system fan module using the back-panel fan module

indicators. See Figure 1-18.

Remove the fan module:

Press the fan-module release button. See Figure 4-3.

Slide the fan module out of the enclosure.

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды