Dell PowerEdge M620 Скачать руководство пользователя страница 337

Страница: 337 / 368

System Board Information

337

PowerEdge M600 Jumper Settings

Figure 7-13 shows the location of the configuration jumpers on the blade

system board. Table 7-8 lists the jumper settings.

NOTE:

Figure 7-13 is oriented with the front end of the blade system board facing to

the right.

Table 7-8. PowerEdge M600 Jumper Settings

PWRD_EN

(default)

The password feature is enabled. (Pins 1-2)

The password feature is disabled. (Pins 2-3)

NVRAM_CLR

(default)

The configuration settings are retained at

system boot (Pins 2-3)
The configuration settings are cleared at the

next system boot. (Pins 1-2) (If the

configuration settings become corrupted to the

point where the system does not boot, install

the jumper and boot the system. Remove the

jumper before restoring the configuration

information.)

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды