Dell PowerEdge M620 Скачать руководство пользователя страница 131

Страница: 131 / 368

About Your System

131

The amount of
system memory has
changed.

Faulty memory module.

See "Troubleshooting Blade

Memory" on page 319. If the

problem persists, see

"Getting Help" on page 361.

This system does
not support
processors greater
than 95W.

Unsupported processor(s)

installed.

Replace the processor(s)

with a supported version.

See "Processors" on

page 243.

Time-of-day clock
stopped.

Faulty battery; faulty blade

board.

See "Troubleshooting Blade

Memory" on page 319. If the

problem persists, see

"Getting Help" on page 361.

Time-of-day not
set — please run
SETUP program.

Incorrect

Time

Date

settings; faulty blade board

battery.

Check the

Time

and

Date

settings. See "Using the

System Setup Program

and UEFI Boot Manager" on

page 137. If the problem

persists, see

"Troubleshooting the

NVRAM Backup Battery" on

page 324.

Timer chip counter
2 failed.

Faulty blade board.

See "Getting Help" on

page 361.

TPM failure

A Trusted Platform

Module (TPM) function

has failed.

See "Getting Help" on

page 361.

Table 1-27. Blade Messages

(continued)

Message

Causes

Corrective Actions

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды