Dell PowerEdge M620 Скачать руководство пользователя страница 159

Страница: 159 / 368

Installing Blade Components

159

Installing a Blade Blank

Hold the blank with the guide rail facing upwards (see detail in

Figure 3-1).

Install the blank in the enclosure:
•

If you are installing a blade blank in one of the eight upper bays

, align

the metal guide rail on the upper edge of the blade blank so that the

guide rail fits between the plastic guides on the enclosure (see detail in

Figure 3-1).

•

If you are installing a blade blank in one of the eight lower bays

, align

the edge of the blank with the plastic guide rail on the floor of the

M1000e enclosure, and slide the blank into the enclosure until the

lower latch engages.

Opening and Closing the Blade

Opening the Blade

Remove the blade from the enclosure. See "Removing a Blade" on

page 155.

Install the I/O connector cover(s). See Figure 3-3.
A full-height blade requires two connector covers.

Orient the blade as shown in Figure 3-3 so that the cover-release latch

faces up.

Lift the cover-release latch and slide the cover toward the back of the blade

until it stops.

Carefully lift the cover away from the blade.

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды