Dell PowerEdge M620 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 368

background image

132

About Your System

TPM configuration
operation is
pending.
Press (I) to
Ignore OR (M) to
Modify to allow
this change and
reset the system.
WARNING: Modifying
could prevent
security

This message is displayed

when the system re-starts

after a TPM configuration

command is entered.

Enter I or M to proceed.

TPM configuration
operation honored.
System will now
reset

TPM configuration

operation command has

been accepted

For information only.

Unsupported CPU
combination.

Mismatched processors are

installed.
Processor is not supported

by the blade.

Replace a processor so that

both processors match. See

"Processors" on page 243.
Check for a BIOS update

using the Dell Support

website at

support.dell.com

.

Unsupported CPU
stepping detected.

Processor is not supported

by the blade.

Check for a BIOS update

using the Dell Support

website at

support.dell.com

.

If the problem persists,

install a supported processor.

See "Processors" on

page 243.

CPU set to minimum
frequency.

The processor speed may

be intentionally set low for

power conservation.

If not an intentional setting,

check any other system

messages for possible causes.

Table 1-27. Blade Messages

(continued)

Message

Causes

Corrective Actions

«
...
130
131
132
133
134
...
»

Содержание PowerEdge M620

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M620

Бренд: ICP Страницы: 19

Бренд: Premier Страницы: 30

Бренд: Overland Storage Страницы: 4

Бренд: Skyworth Страницы: 71

Бренд: Xena Networks Страницы: 6

Бренд: WP Страницы: 30

Бренд: abaco systems Страницы: 9

DMC 1000 - Modular Expansion Base

Бренд: D-Link Страницы: 16

Бренд: Supermicro Страницы: 72

RM16M - Versatile Rack Mounting Chassis

Бренд: Telenetics Страницы: 49

Бренд: Svive Страницы: 8

Бренд: CTC Union Страницы: 2

Бренд: CTC Union Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды