Dell PowerEdge M620 Скачать руководство пользователя страница 212

Страница: 212 / 368

212

Installing Blade Components

Non-Optimal Memory Configurations

System performance can be affected if your memory configuration does not

conform to the preceding installation guidelines. Your system may issue an

error message during start-up stating that your memory configuration is non-

optimal.

Memory Sparing Support – PowerEdge M600

Memory sparing requires eight identical memory modules. The memory sparing

feature must also be enabled in the System Setup program, and can be used

only if memory mirroring is not enabled.
Table 3-15 shows how memory sparing splits the available and spared memory

in each memory module configuration.

Memory Mirroring Support – PowerEdge M600

The system supports memory mirroring if eight identical memory modules are

installed in the system. Mirroring must be enabled in the System Setup program

and can be used only if memory sparing is not enabled. In a mirrored

configuration, the total available system memory is one-half of the total

installed memory.

Table 3-15. Memory Sparing Configurations

–

PowerEdge M600

DIMMs

Size/Type

Total Memory

Available

Spare

512 MB

4 GB

2 GB

1 GB single-rank

8 GB

4 GB

2 GB dual-rank

16 GB

12 GB

4 GB

4 GB dual-rank

32 GB

24 GB

8 GB

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды