Dell PowerEdge M620 Скачать руководство пользователя страница 324

Страница: 324 / 368

324

Troubleshooting Your System

Troubleshooting the NVRAM Backup Battery

Each blade contains a battery that maintains the blade configuration, date,

and time information in NVRAM when you turn off the blade. You may need

to replace the battery if an incorrect time or date is displayed during the boot

routine.
You can operate the blade without a battery; however, the blade configuration

information maintained by the battery in NVRAM is erased each time you

remove power from the blade. Therefore, you must re-enter the system

configuration information and reset the options each time the blade boots

until you replace the battery.

Re-enter the time and date through the System Setup program. See "Using

the System Setup Program and UEFI Boot Manager" on page 137.

Remove the blade for at least one hour. See "Removing a Blade" on

page 155.

Install the blade. See "Installing a Blade" on page 158.

Enter the System Setup program.
If the date and time are not correct in the System Setup program, replace

the battery. See "Blade System Board NVRAM Backup Battery" on

page 265.
If the problem is not resolved by replacing the battery, see "Getting Help"

on page 361.

NOTE:

If the blade is turned off for long periods of time (for weeks or months), the

NVRAM may lose its system configuration information. This situation is caused by a

defective battery.

NOTE:

Some software may cause the blade’s time to speed up or slow down. If the

blade seems to operate normally except for the time kept in the System Setup

program, the problem may be caused by software rather than by a defective

battery.

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды