Dell PowerEdge M620 Скачать руководство пользователя страница 128

Страница: 128 / 368

128

About Your System

Memory tests
terminated by
keystroke.

The spacebar or ESC key

was pressed during POST

to terminate the memory

test.

Information only.

Keyboard data line
failure.

Keyboard cable connector

loose or improperly

connected. Keyboard or

keyboard/mouse controller

may be faulty.

Ensure that the keyboard is

properly connected. If the

problem persists, see

"Getting Help" on page 361.

Keyboard stuck key
failure.

Keyboard fuse has
failed.

Overcurrent detected in

the keyboard connector.

See "Getting Help" on

page 361.

No boot device
available.

Faulty or missing diskette

drive, optical drive, or hard

drive.

Check the

Integrated

Devices

configuration

settings in the System Setup

program and ensure that the

controller for the boot

device is enabled. See "Using

the System Setup Program

and UEFI Boot Manager" on

page 137. Ensure that the

controller for the boot

device is enabled.
If the problem persists,

replace the drive. See "Hard

Drives" on page 267.

No boot sector on
hard-disk drive.

An operating system is not

on the hard drive.

Check the hard-drive

configuration settings in the

System Setup program. See

"Using the System Setup

Program

and UEFI Boot Manager" on

page 137.

No timer tick
interrupt.

Faulty blade board.

See "Getting Help" on

page 361.

Not a boot
diskette.

Not a bootable diskette.

Use a bootable diskette.

Table 1-27. Blade Messages

(continued)

Message

Causes

Corrective Actions

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды