Dell PowerEdge M620 Скачать руководство пользователя страница 117

Страница: 117 / 368

About Your System

117

Current Overlimit
detected in
Expansion

Applicable to both base

blade and expansion.

NOTE:

Applicable to M610x

only.

Verify that the PCIe

expansion cards installed do

not have power

consumption more than

250 W. For more

information, see "Expansion

Card Installation

Guidelines" on page 235.

Failsafe detected
in PCIe expansion
on mini planar

Check the system event

log for critical failure

events.

NOTE:

Applicable to M610x

only.

See "Getting Help" on

page 361.

Global PFault
detected in
Expansion

A PFault has occurred in

the expansion.

NOTE:

Applicable to M610x

only.

See "Getting Help" on

page 361.

PCIe card inserted
in slot X [Vendor
ID: YYYY Device
ID: ZZZZ]

A new PCIe card has been

installed.

For information only.

PCIe card removed
from slot X

A PCIe expansion card was

removed.

Re-install the expansion

card. See "Installing an

Expansion Card" on

page 236.

Invalid PCIe card
found in the
Internal Storage
slot!

The system halted because

an invalid PCIe expansion

card is installed in the

dedicated storage

controller slot.

Remove the PCIe expansion

card and install the

integrated storage controller

in the dedicated slot. See

"Storage Controller Card" on

page 281.

Table 1-27. Blade Messages

(continued)

Message

Causes

Corrective Actions

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды