Dell PowerEdge M620 Скачать руководство пользователя страница 121

Страница: 121 / 368

About Your System

121

Alert: DIMM_

[m]

and DIMM_[

must

be populated with
a matched set of
DIMMs if more than
1 DIMM is present.
The following
memory DIMMs have
been disabled.

The installed memory

configuration is invalid.

Ensure that the memory

modules are installed in

matched pairs. See "System

Memory" on page 171.

Alert! Node
Interleaving
disabled! Memory
configuration does
not support Node
Interleaving.

The installed memory

configuration does not

support node interleaving.

Install a memory

configuration that supports

node interleaving. See

"System Memory" on

page 171.

Alert! Redundant
memory disabled!
Memory
configuration does
not support
redundant memory.

The installed memory

configuration does not

support redundant

memory.

Install a memory

configuration that supports

redundant memory. See

"System Memory" on

page 171.
Disable the

Redundant

Memory

option in the

System Setup program. See

"Using the System Setup

Program

and UEFI Boot Manager" on

page 137.

Alert! Redundancy
was previously
lost. Power cycle
required to
reconfigure
redundant memory.

Memory error.

Power cycle the blade.

Table 1-27. Blade Messages

(continued)

Message

Causes

Corrective Actions

Содержание PowerEdge M620

















































































































































































































































































































































































Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды

Dell PowerEdge M620, Руководство пользователя

Результаты поиска

Содержание PowerEdge M620

Отзывы:

Похожие инструкции для PowerEdge M620

Бренды по названию

Популярные бренды