Covidien Newport e360 Скачать руководство пользователя страница 118

Страница: 118 / 154

Operational Verification

6-6

Service Manual

6.5.2

Circuit Leak Test

Figure 6-3.

Circuit Leak Test



Note:

The circuit check test can only be performed in ventilation standby.

Remove test lung, if present, and occlude the end of the patient circuit Y-piece using CAP100P.

Turn on the ventilator.

Touch the

Circuit Check

button on the screen, and follow the on-screen instructions.

After the test is completed, verify that the message “PASSED” is displayed. Document the results on the
record sheet.

Reattach the test lung.

To exit ventilation standby, touch the

Start Ventilating

button on the screen.

6.5.3

Exhalation Flow Sensor and FiO

Sensor Calibration

Touch the

Sensors

button on the screen.

Touch the

Flow Sensor

button on the screen, and follow the on-screen instructions.

Содержание Newport e360



























































































































































Результаты поиска

Содержание Newport e360

Отзывы:

Похожие инструкции для Newport e360

Бренды по названию

Популярные бренды

Covidien Newport e360, Руководство по обслуживанию

Результаты поиска

Содержание Newport e360

Отзывы:

Похожие инструкции для Newport e360

Бренды по названию

Популярные бренды