Covidien Newport e360 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 154

background image

Component Removal and Replacement

4-4

Service Manual

4.5.2

Exhalation Flow Sensor Cable (Outside) (GR-CBL2123P)

To replace the exhalation flow sensor cable, perform the following steps:

1.

Remove the exhalation valve and exhalation flow sensor by following the steps in section

(EXH2105A) and Flow Sensor (FLS2101P)

2.

Remove the exhalation flow sensor cable (outside) (GR-CBL2123P) from the exhalation manifold by
pulling the collet of the cable connector.



Note:

The lock mechanism of the connector can be easily released by pulling the collet of the connector. Do NOT
disconnect the connector by pulling the wire.

3.

Reinstall the cable to the exhalation manifold by aligning the key on the connector with the notch of the
female connector on the exhalation manifold.

4.6

Top Cover (CVR2101M)

Figure 4-2.

Top Cover

1

Screws (three of six securing cover to ventilator)

«
...
62
63
64
65
66
...
»

Содержание Newport e360



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Newport e360

Бренд: UnionSpecial Страницы: 56

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: Patty-O-Matic Страницы: 28

Pressure Governor

Бренд: Waterous Страницы: 53

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

ActiveFinder One

Бренд: LaserLiner Страницы: 92

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Бренд: Fast Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды