Covidien Newport e360 Скачать руководство пользователя страница 99

Страница: 99 / 154

Diagnostic Mode

Service Manual

5-3

Visually inspect the ventilator for cosmetic defects, damage, or missing items.

Before removing the top cover, unplug the ventilator from the AC power and gas sources.

Remove the six screws on the back panel that secure the top cover to the ventilator.

Remove the top cover by performing the steps in section

4.6

, “

Top Cover (CVR2101M)

.”

Reconnect the AC power to the ventilator.

Connect both air and oxygen supply gas sources to the ventilator.

Verify supply gas sources are at 50 ±2 psig.

Prior to starting the calibration procedure, verify that all test equipment is in current calibration status.

5.4

Diagnostic Mode

Most of the calibrations on the ventilator are performed in the diagnostic mode. This mode enables
you to perform PSOL valve, exhalation valve, and regulator calibrations.

To enter diagnostic mode, perform the following steps:

Confirm the ventilator is off and connected to AC power.

Press and hold the

Accept

button while turning on the ventilator.

Release the

Accept

button when the logo screen is displayed.

Wait for a few minutes until the

Software Download/Diagnostics Mode

screen is displayed (see

Figure 2-

19.

Table 5-1.

Diagnostic Mode

Diagnostic mode

Calibration

N/A

Air PSOL valve

Oxygen PSOL valve

Manual flow adjustment

Exhalation PSOL valve

Analog PCB

N/A

Exhalation flow sensor

Содержание Newport e360



























































































































































Результаты поиска

Содержание Newport e360

Отзывы:

Похожие инструкции для Newport e360

Бренды по названию

Популярные бренды

Covidien Newport e360, Руководство по обслуживанию

Результаты поиска

Содержание Newport e360

Отзывы:

Похожие инструкции для Newport e360

Бренды по названию

Популярные бренды