Covidien Newport e360 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 154

background image

Maintenance, Overhaul, and Software Upgrade

2-24

Service Manual

3.

When the

Logo

screen is displayed, release the

Accept

button.

4.

Wait for a few minutes until the

Software Download/Diagnostics Mode

screen is displayed (see

Figure 2-19.

Software Download / Diagnostics Mode Screen

5.

Connect the USB flash drive (with latest software) to the USB port on the back panel of the ventilator
(see

for USB port location).

6.

Touch

Start Download

on the

Software Download/Diagnostics Mode

screen (

). The ventilator

will sound a short beep and the message “Touch Selection to Begin” changes to a flashing message
stating “downloading….” Depending on the software version your ventilator is currently running, the
download may take anywhere from 2 minutes to 45 minutes.

7.

When the software download is complete, the ventilator will sound a short beep. The message
“Download Complete” is displayed.

8.

Turn the ventilator off.

9.

Wait at least 10 seconds, and then turn the power back on.

10.

When the message “Ventilation Standby” appears, touch

Start Ventilating

to begin ventilating.



Note:

Because air/O

2

gas supplies are not connected, the Air/O

2

Loss alarm will sound. Disregard the alarm while

verifying the software is installed correctly.

11.

Confirm the message “Incompatible Software ….” does not appear on the screen. If this message
appears on the screen, the software download was NOT completed successfully. Repeat steps 1–6
again. If the download is unsuccessful again, contact the Technical Service Department for further
assistance.

12.

Press the

Extended Functions

button on the front control panel.

13.

Touch the

Event History

button on the screen.

«
...
46
47
48
49
50
...
»

Содержание Newport e360



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Newport e360

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Бренд: Zenbooth Страницы: 60

Бренд: Federal Страницы: 43

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Lab companion SI-300

Бренд: Jeio tech Страницы: 69

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 4

Бренд: Jct Страницы: 16

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: M-Audio Страницы: 25

STOMAMED COL-160

Бренд: Orliman Страницы: 12

Бренд: RAM Страницы: 4

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Бренд: Daihan Scientific Страницы: 27

WEEDDEVIL ST-97

Бренд: R+M Suttner Страницы: 16

Бренд: Viking Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды