manualshive.com logo in svg

Covidien Newport e360, Руководство по обслуживанию

Поделиться
Скачать
Covidien Newport e360 Скачать руководство пользователя страница 108

Calibration Procedures

5-12 

 Service Manual

Exhalation PSOL Regulator

1.

Remove the orange tubing from the IN exhalation PSOL valve port and connect to a calibrated high 
pressure gauge (see 

Figure 5-4.  

).

2.

Using a flat head screwdriver, adjust the exhalation PSOL regulator, which is located near the exhalation 
PSOL valve, to between 15.0 psig and 15.5 psig.

3.

Reconnect the orange tubing to the IN exhalation PSOL valve port. 

Figure 5-4.  

Exhalation PSOL/Safety Regulator

Safety Regulator

1.

While in diagnostics mode d3, adjust 

Flow

 to 3 L/min.

2.

Disconnect the patient circuit from the exhalation valve, and connect it to the Y-piece of the patient 
circuit. This creates a closed loop.

3.

Tee in a low-pressure gauge in the patient circuit.

4.

Using a flat head screwdriver, adjust the safety regulator (see 

Figure 5-4.  

) to obtain a 

machine 1

 pressure 

reading of 140 ±5 cmH

2

O on the screen.

1

Orange tubing to exhalation 
PSOL valve IN port

3

Exhalation PSOL regulator

2

Exhalation PSOL valve

4

Safety regulator

Содержание Newport e360



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды