Control Techniques SM-Universal Encoder Plus Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 112

Control Techniques SM-Universal Encoder Plus Скачать руководство пользователя страница 16

16

SM-Universal Encoder Plus User Guide

www.controltechniques.com

Issue Number: 6

3.4.7

Linear Encoders

Linear Quadrature / SinCos Encoder

These types of encoder are purely incremental and have no information for
commutation. With this type of feedback the Unidrive SP must carry out a phasing test
to find the phase offset angle on every power up for operation in servo mode.

Digital Hall Linear Quadrature / SinCos Incremental encoder

These types of encoder have digital hall effect signals U, V, W plus complements that
supply the necessary signals for deriving the position at power-up. The quadrature
signals, incremental or SinCos are used for speed feedback. A flux alignment test is
required during set-up to determine the phase offset angle for operation in servo mode.

Linear Absolute SinCos encoder

These types of encoder derive the absolute position at power-up via the comms
protocol, Hiperface, EndAt or SSI with the incremental signals, SinCos, being used for
incremental position and speed feedback.

A flux alignment test is required during set-up to determine the phase offset angle for
operation in servo mode.

Linear Absolute encoder

These types of feedback are comms only encoders, which derive the position at power-
up via either the EndAt or SSI comms protocols. The position feedback is also passed
via comms during operation. The comms only encoders operate with the drive being the
master and passing the required clock signal. A flux alignment test is required during

set-up to determine the phase offset angle for operation in servo mode.

Limitations

Type

Encoder

Max Baud

Rate (bits/sec)

Max Speed

rpm

Comms Only

EndAt

2Mbits/sec

40,000rpm

SSI

2Mbits/sec

The SSI input at default is configured to operate in Gray code through Pr

x.18

, this can

be configured to operate in binary format by setting Pr

x.18

= 1. The simulated SSI

encoder output will operate with both binary format and Gray code, the mode being
configured through Pr

x.28

.

NOTE

A flux alignment test is required during set up to determine the phase offset angle for
operation in servo mode.

NOTE

Type

Encoder

Description

Pr x.15

Linear

encoder

Ab

Linear quadrature encoder

0

SC

Linear SinCos encoder

6

Ab.SErvo

Digital hall Linear quadrature incremental encoder

3

SC.SErvo

Digital hall Linear SinCos incremental encoder

12

SC.HiPEr

Linear absolute SinCos encoder

7

SC.EndAt

9

SC.SSI

11

EndAt

Linear absolute encoder

8

SSI

10

Refer to section 3.4.2

SinCos encoder feedback signals

on page 10 for further

information on the SinCos encoder feedback signals.

NOTE

«
...
14
15
16
17
18
...
»

Содержание SM-Universal Encoder Plus

















































































































Отзывы:

Нет отзывов