manualshive.com logo in svg

Control Techniques SM-Universal Encoder Plus, Руководство пользователя, Страница: 83 / 112

Поделиться
Скачать
Control Techniques SM-Universal Encoder Plus Скачать руководство пользователя страница 83

SM-Universal Encoder Plus User Guide

83

Issue Number:  6

www.controltechniques.com

The UVW commutation signals are used to define the motor position during the first 
120° electrical rotation after the drive is powered-up or the encoder is initialised.

6, SC: SinCos encoder with no serial communications

This type of encoder gives incremental position and can only be used for control in 
Closed-loop vector mode.

7, SC.HiPEr: Absolute SinCos encoder using Stegmann 485 comms protocol 
(HiperFace). 

This type of encoder gives absolute position and can be used for motor control in 
closed-loop vector or servo modes. The Solutions Module can check the position from 
the sine and cosine waveforms against the internal encoder position using serial 
communications and if an error occurs the Solutions Module trips the drive. Additional 
communications with the encoder is possible. 

8, EndAt: Absolute EndAt only encoder

This type of encoder gives absolute position and can be used for motor control in 
closed-loop vector or servo modes. Additional communications with the encoder is not 
possible.

9, SC.EndAt: Absolute SinCos encoder using EndAt comms protocol

This type of encoder gives absolute position and can be used for motor control in 
closed-loop vector or servo modes. The Solutions Module can check the position from 
the sine and cosine waveforms against the internal encoder position using serial 
communications and if an error occurs the drive trips. Additional communications with 
the encoder is possible.

10, SSI: Absolute SSI only encoder

This type of encoder gives absolute position and can be used for motor control in 
closed-loop vector or servo modes. Additional communications with the encoder is not 
possible. SSI encoders use either gray code or binary format which can be selected with 
Pr 

x.18

. Most SSI encoders use 13 bit single turn position information, and so Pr 

x.11

 

should normally be set to 13. If the single turn resolution of the encoder is lower then the 
least significant bits of the data are always zero. Some SSI encoders use the least 
significant bit to show the status of the encoder power supply. In this case the single turn 
position resolution should be set to include this bit, but the Solutions Module should be 
set up to monitor it via Pr 

x.17

. Some SSI encoders use a right shifted format where the 

unused single turn position bits are removed instead of being set to zero. For these 
encoders the single turn position resolution should be set to the number of bits used for 
the single turn position.

11, SC.SSI: SinCos encoder using SSI comms protocol

This type of encoder gives absolute position and can be used for motor control in 
Closed-loop vector or Servo modes. The drive can check the position from the sine and 
cosine waveforms against the internal encoder position using serial communications 
and if an error occurs the drive trips. 

12, SC.SErvo: SinCos encoder with UVW communication outputs

The type of encoder gives absolute position and can be used for motor control in 
closed-loop vector or servo modes. U, V, W commutation outputs are required with a 
SinCos type encoder when used with a servo motor. The U, V, W commutation outputs 
are used to define the motor position during the first 120° electrical rotation after the 
drive is powered-up or the encoder is initialised.

If an Absolute SSI only encoder is used with a data transfer rate of 

>

30

µ

s timing 

problems may occur, resulting in speed feedback instability.

NOTE

Содержание SM-Universal Encoder Plus

















































































































Отзывы:

Нет отзывов