Control Techniques SM-Universal Encoder Plus Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 112

Control Techniques SM-Universal Encoder Plus Скачать руководство пользователя страница 95

SM-Universal Encoder Plus User Guide

95

Issue Number: 6

www.controltechniques.com

transmit and receive registers. The transmission system can be used to communicate
with encoders provided the mode is either SC.HiPEr or SC.EndAt.

At power-up Pr

x.45

is initially zero, but is set to one when the encoder connected to

position module has been initialised. The drive cannot be enabled until this parameter is
one.

If the encoder power-supply is lost, or the encoder type parameter is changed for an
encoder connected to a Solutions Module, and the encoder type is SC, SC.HiPEr,
SC.EndAt or EndAt the encoder will no longer be initialised. When an encoder is no
longer initialised Pr

x.45

is reset to zero and the drive cannot be enabled. The encoder

may be re-initialised, provided the drive is not active, by setting Pr

3.47

to one. Pr

x.45

is automatically reset to zero when the initialisation is complete.

The LPR divider Pr

x.46

is used to scale the equivalent lines per revolution in Pr

x.10

of

incremental and SinCos encoders, without comms, on rotary motors, and all but comms
only encoders on linear motors. (Servo encoders must have the same number and pitch
of poles as the motor.)

The equivalent line per revolution parameter (Pr

x.10

) is divided by the value in Pr

x.46

.

This can be used when an encoder is used with a linear motor where the number of
counts or sine waves per pole is not an integer.

Example

128.123 lines per revolution would be set as 128123 in Pr

x.10

and 1000 in Pr

x.46

giving:

128123 / 1000 = 128.123. If the value is less than 1, the value used will be 1.

When using SinCos encoders with comms, the comms and SinCos positions must be
aligned. The comms position resolution may be a multiple of the analogue position
resolution. When a linear encoder type has been selected (Pr

x.16

= 0) the value in Pr

x.09

is this multiple.

The motor pole pitch used to configure EndAt and Hiperface encoders is that of the
currently selected motor map.

For further detailed information refer to Chapter 8

Advanced Operation

NOTE

x.45

Position feedback initialised

RO

Bit

NC

PT

Ú

Ö

Update rate: Background write

x.46

Line per revolution divider

RW

Uni

US

Ú

1 to 1024

Ö

1

Update rate: Background read

When setting larger values in Pr

x.10

when the Solutions Module is the main feedback

device, the drive will limit the maximum speed, which in turn limits the maximum of
some of the drive parameters such as Pr

1.06

and Pr

1.21

. If the overall value of the

LPR after division is low once more, the parameters that have been limited will not
return to their original values and may need to be increased. An ELPR of 10,000 gives
a maximum speed of 3000rpm.

NOTE

«
...
93
94
95
96
97
...
»

Содержание SM-Universal Encoder Plus

















































































































Отзывы:

Нет отзывов