Canon imageRUNNER ADVANCE 9070 PRO series, Справочник по обслуживанию, Страница: 746 / 874

5
5-518
SORTER> ADJUST
STP-R3 Adj A4R rear stpl pstn (<45 deg): Fin-B1
Lv.1 Details To adjust the one rear staple position on the A4R size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case When misalignment occurs at the rear staple position on A4R size
paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-6 to 6
Unit 0.49 mm
Appropriate target value 0
Default value
0
STP-R4 Adj LTRR rear stpl pstn (<45 deg):Fin-B1
Lv.1 Details To adjust the one rear staple position on the LTRR size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
Use case When misalignment occurs at the rear staple position on LTRR size
paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-6 to 6
Unit 0.49 mm
Appropriate target value 0
Default value
0
SW-UP-RL Adj of Swing Roller falling pstn: Fin-B1
Lv.1 Details To adjust the Swing Roller down position.
As the value is incremented by 1, the Swing Roller down position
moves downward by 0.2mm.
Use case When paper fails to be transported to the Processing Tray and
misalignment occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-17 to 33
Unit 0.2 mm
Appropriate target value 0
Default value
0
PUN-V-RG Adj of punch vertical rgst pstn: Fin-B1
Lv.1 Details To adjust the vertical registration position of the paper to be punched.
As the value is incremented by 1, the punch hole position moves
toward the edge by 1mm.
Use case When misalignment of punch hole position occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-4 to 2
Unit 1 mm
Appropriate target value 0
Default value
0
SORTER> ADJUST
PRCS-RET Adj Process Tray return amount: Fin-B1
Lv.1 Details To adjust the pull-back amount of the paper on the Processing Tray.
As the value is incremented by 1, the pull-back amount is decreased
by 1.4mm.
Use case When the paper is bent in the Processing Tray
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 5
Unit 1.4 mm
Appropriate target value 0
Default value
0
UP-CL Setting of upward curl prev mode: Fin-B1
Lv.1 Details Set 1 when upward curl occurs on the paper delivered to the Stack
Tray, and paper leaning due to the curl occurs.
Use case When upward curl occurs on the paper delivered to the Stack Tray,
and paper leaning due to the curl occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value 0
DW-CL Setting downward curl prev mode: Fin-B1
Lv.1 Details Set 1 when downward curl occurs on the paper delivered to the
Stack Tray, and paper leaning due to the curl occurs.
Use case When downward curl occurs on the paper delivered to the Stack
Tray, and paper leaning due to the curl occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value 0
THC-CL Setting heavy ppr curl prev mode:Fin-B1
Lv.1 Details Set 1 when upward curl occurs on the heavy paper delivered.
When 1 is set, the amount of Stack Tray descension for stack
delivery increases. The paper surface detection is performed for
every sheet, not for every 5 sheets.
Use case When upward curl occurs on the heavy paper delivered
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value 0