Canon imageRUNNER ADVANCE 9070 PRO series Скачать руководство пользователя страница 600

Страница: 600 / 874

5-372

COPIER> OPTION> NETWORK

ILOGMODE

Setting of IP address block mode

Lv.1 Details

To set all protocols or TCP/UDP/ICMP unicast as the target of IP

block.

When 0 is set, the machine responds to ARP, ICMP multicast and

broadcast which have no direct relation, and consequently the

number of logs is increased.

When 1 is set, the machine filters TCP, UDP and ICMP unicast only.

Use case

Upon user’s request

Adj/set/operate method 0 to 3

0: All protocols support mode

1: TCP/UDP/ICMP unicast support mode

2, 3: Not used

Default value

ILOGKEEP

Set of IP address block log hold time

Lv.1 Details

To set the retention time from the log time of IP block.

When access is made again from a same IP address which was

blocked before, if it is within the retention time of the previous log, its

log is not recorded.

If access is frequently made from a same IP address, the log record

of the UI might be filled with its logs. If the user considers that a

single log for a same IP address is enough, set the longer retention

time.

Use case

Upon user’s request

Display/adj/set range

0 to 48

0: 1 minute (special mode)

1 to 48: 1 hour to 48 hours

Default value

IPTBROAD

Set to allow broad/multi cast TX

Lv.1 Details

To set whether to permit transmission of broadcast packets and

multicast packets.

Transmission of broadcast packets and multicast packets is

permitted without specifying an exception address. It is permitted

within the device even if it is rejected in the default setting of the

IPv4/v6 transmission filter.

Set “1: Disabled” when the user does not want to send them.

Use case

Upon user’s request

Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range

0 to 5

0: Enabled, 1: Disabled, 2 to 5: Not used

Default value

COPIER> OPTION> NETWORK

PFWFTPRT

Set of RST reply at IP filter FTP SEND

Lv.1 Details

When FTP SEND is executed using an IP filter by which packets

from a specific remote PC are rejected, SYN is returned to the port

113 if the PC supports authentication of the FTP port 113. However,

since the IP filter blocks the packets, the block logs are increased

and the performance is lowered.

When 1 is set, RST is returned to the port 113 without blocking

packets.

Use case

When executing FTP SEND against the OS which supports

authentication of the FTP port 113 while the IP filter is enabled

Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range

0 to 1

0: OFF, 1: ON

Default value

PRNIPBLK

ON/OFF of IP address block function

Lv.1 Details

To set ON/OFF of IP address block function.

When 1 is set, “IP Address Range Settings” and “RX/Print Range”

screen is displayed on the Control Panel.

Use case

When using the IP address block function

Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range

0 to 1

0: OFF, 1: ON

Default value

Related user mode

Preferences> Network> TCP/IP Settings> IPv4 Settings/IPv6

Settings> IP Address Range Settings> RX/Print Range

IPMTU

Setting of MTU size

Lv.1 Details

To set MTU size of network packet.

This item is used when performing SEND communication between

locations connected with Ethernet in a field environment where MTU

black hole problem occurs.

Use case

When MTU black hole problem occur

Adj/set/operate method Enter the setting value, and then press OK key.
Caution

With IPv6, use of MTU which size is less than 1280 bytes is not

recommended by RFC. Therefore, when setting IPv6 to ON and MTU

to 7 or smaller, communication using IPv6 may not be available.

Display/adj/set range

1 to 10

1: 600 byte, 2: 700 byte, ..., 9: 1400 byte, 10: 1500 byte

Unit

100 byte

Default value

Содержание imageRUNNER ADVANCE 9070 PRO series











































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание imageRUNNER ADVANCE 9070 PRO series

Отзывы:

Canon imageRUNNER ADVANCE 9070 PRO series, Справочник по обслуживанию, Страница: 600 / 874

Результаты поиска

Содержание imageRUNNER ADVANCE 9070 PRO series

Отзывы: