Canon imageRUNNER ADVANCE 9070 PRO series Скачать руководство пользователя страница 450

Страница: 450 / 874

5-222

COPIER> ADJUST> HV-PRI

PRI-FREQ

Adjustment of YMC charging AC frequency

Lv.2 Details

To adjust the charge AC frequency for Y, M and C.

As the value is smaller, moire is likely to occur.

Use case

At a charge failure

Adj/set/operate method 1) Select the items.

2) Enter the setting value, and then press OK key.

Caution

• Do not use this at the normal service.

• Be sure to perform discharge current control (COPIER>

FUNCTION> MISC-P> DISCHG) after the execution.

Display/adj/set range

0 to 2

Default value

DHT-ON

Forcible ON of Drum Heater (Bk)

Lv.2 Details

To forcibly turn ON the Drum Heater (Bk) regardless of the

environment when the power is turned ON.

Use case

When the density of Bk gets lower at the end of the continuous print

Adj/set/operate method Select the item, and then press OK key.
Caution

Do not use this at the normal service.

T-5-39

■

HV-TR

COPIER> ADJUST> HV-TR

PRE-TR

Set Pre-transfer charge current adj VL

Lv.1 Details

To set the output adjustment value of pre-transfer charging current.

When the toner scattering occurs at the image end side, decrease

the value.

As the value is increased by 1, the current is increased by 5 uA.

Use case

• When replacing the DC Controller PCB/clearing RAM data

• When an image failure occurs (leopard patterns on Bk solid image)

Adj/set/operate method Enter the setting value, and then press OK key.
Caution

Do not use this at the normal service.

Display/adj/set range

-30 to 40

Unit

5 uA

Default value

2TR-TGT1

Sec trns indiv set target currnt: set 1

Lv.2 Details

To adjust the target current of secondary transfer for setting 1.

Setting 1 is the combination condition of environment, paper type

(paper weight), color mode and feed side that are set in TR-ENV1,

TR-PPR1, TR-CLR1 and TR-DUP1. When this condition is satisfied,

the target current that is set here is applied to the Secondary

Transfer Outer Roller.

When low-voltage mottled image or toner scattering on solid image

occurs, increase the current.

When high-voltage mottled image or density loss due to excessive

transfer occurs, decrease the current.

As the value is incremented by 1, the current changes by 2 uA.

+: Increase

-: Decrease

Use case

When an image failure occurs on all paper types (mottled image,

density loss due to excessive transfer, toner scattering on solid

image, etc.)

Adj/set/operate method Enter the setting value, and then press OK key.
Caution

Increase/decrease the value by 1 while checking the symptom each

time.

Display/adj/set range

-10 to 10

Unit

2 uA

Default value

Related service mode

COPIER> ADJUST> HV-TR> TR-ENV1, TR-PPR1, TR-CLR1, TR-

DUP1, 2TR-SHR1

Содержание imageRUNNER ADVANCE 9070 PRO series











































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание imageRUNNER ADVANCE 9070 PRO series

Отзывы:

Canon imageRUNNER ADVANCE 9070 PRO series, Справочник по обслуживанию, Страница: 450 / 874

Результаты поиска

Содержание imageRUNNER ADVANCE 9070 PRO series

Отзывы: