Canon imageRUNNER ADVANCE 9070 PRO series, Справочник по обслуживанию, Страница: 480 / 874

5
5-252
COPIER> ADJUST> MISC
WT-FL-LM Wst tonr full warning dis timing set
Lv.1 Details To set the timing to display the waste toner full warning message.
Depending on the user’s use condition (image duty), the number of
images to be printed until the Waste Toner Container becomes full is
different. By specifying the image duty, the number of images to be
printed until the toner full warning message can be set.
If the image duty is approx. 10%, set to “1” since Waste Toner
Container becomes full with approx. 120,000 images (B&W).
Toner full warning message is displayed when the number of images
reaches the setting value or when the Waste Toner Full Sensor is
ON. If 4,000 images are printed further, the device stops.
Use case When toner full warning timing is adjusted according to the user’s
use condition
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution After replacing the Waste Toner Container, clear the counter using
W-TN-CLR.
Display/adj/set range 0 to 4
0: Image duty: 30% (B&W 40,000 images)
1: 10% (120,000 images)
2: 5 to 7% (240,000 images)
3: 3.75% or less (320,000 images)
4: Not used
Default value 1
Related service mode COPIER> FUNCTION> CLEAR> W-TN-CLR
REOS-PG Set Reos processing coeffct at 1200dpi
Lv.2 Details To set an optimal Reos processing coefficient for 1200dpi print.
Print PG of the type 55 in COPIER> TEST> PG> TYPE, check the
images in the 4 areas of this PG, and specify the number of the area
in which the character proportion and line width become optimum by
the Reos processing module in the case of PDL1200 dpi setting.
After the setting is done, output the vertical and horizontal patterns
with 3 dots and 10 spaces, which are the same as the PG above,
in 1200 dpi, and confirm that the result is the same as the specified
area.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 4
Default value 2
Related service mode COPIER> TEST> PG> TYPE
COPIER> ADJUST> MISC
SEG-ADJ3 Set text/photo jdgmt stdrd: back side
Lv.1 Details To set the judgment level of text/photo original in Text/Photo/Map
mode (back side at duplex reading with 1 path).
As the value is increased, the original tends to be detected as a
photo document, and as the value is decreased, the original tends to
be detected as a text document.
Use case When adjusting the classification level of text and photo in Text/
Photo/Map mode (back side at duplex reading with 1 path)
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -4 to 4
Default value 0
K-ADJ3 Set Bk text jdgmt stdrd: back side
Lv.1 Details To set the judgment level of black characters at text processing (back
side at duplex reading with 1 path).
As the value is increased, the text tends to be detected as black.
Use case When preferring the text to be judged as black (back side at duplex
reading with 1 path)
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -3 to 3
Default value 0
ACS-ADJ3 Set ACS B&W/color jdgmt stdrd:back side
Lv.1 Details To set the judgment level of B&W/color original in ACS mode (back
side at duplex reading with 1 path).
As the value is increased, the original tends to be detected as a
B&W document, and as the value is decreased, the original tends to
be detected as a color document.
Use case When adjusting the color detection level in ACS mode (back side at
duplex reading with 1 path)
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -3 to 3
Default value 0