D.168
ENGINE
• Using a thickness meter, measure the thrust clearance at some
points between the crankcase and the thrust washer.
Standard
Crankshaft thrust clearance: 0,050-0,100 mm
(0.00197-0.00394 in)
Specific tool: Thickness gauge
If the thrust clearance exceeds the specified range, adjust it by fol-
lowing these steps:
• Remove the thrust shim and measure its thickness with a microm-
eter.
• Change the thrust shim if its thickness is incorrect.
• Measure the thrust clearance again as previously described.
Specific tool: Micrometer (0-25 mm, 0-0.9842 in)
Checking that the shim thickness is in the standard range
INSTALLING THE TRANSMISSION, THE CRANKSHAFT AND THE CONNECTING
ROD
Refer to the sections on engine assembly and installation for instructions on how to install these engine parts.
* ENGINE ASSEMBLY ................................................................................................. Refer to pages D-40/D-80.
* ENGINE INSTALLATION ........................................................................................... Refer to pages D-13/D-19.
Unit: mm/in
Part no.
Thrust shim thickness
800097666
1,925-1,950 (0.07579-0.07677)
800097667
1,950-1,975 (0.07677-0.07775)
800097668
1,975-2,000 (0.07775-0.07874)
800097669
2,000-2,025 (0.07874-0.07972)
800097670
2,025-2,050 (0.07972-0.08070)
800097671
2,050-2,075 (0.08070-0.08169)
800097672
2,075-2,100 (0.8169-0.08267)
800097673
2,100-2,125 (0.08267-0.08366)
800097674
2,125-2,150 (0.08366-0.08464)
800097675
2,150-2,175 (0.08464-0.08562)
Содержание Navigator
