B.17
MAINTENANCE
OIL FILTER SUBSTITUTION
• Drain the engine oil following the same procedure described for
the oil change.
• Remove the oil filter 1 utilising the appropriate wrench (special
tool).
• Apply a light layer of engine oil to the gasket of the new filter be-
fore assembly.
• Assemble the new filter by screwing it in by hand until the gasket
comes into contact with the oil filter container. Tighten by two turns
utilising the oil filter wrench (special tool).
Special tool: 800096659: Oil filter wrench
Tighten the filter correctly by utilising the special wrench.
Never tighten the oil filter by hand.
• Refill with new engine oil and check the level by following the same
procedure used for the oil change.
OIL CAPACITY
Oil change: 3.1 litres
Oil filter change: 3.3 litres
Engine overhaul: 3.6 litres
Utilise only ORIGINAL CAGIVA OIL FILTERS. Filters and
spare parts of other makes could differ with regards to the
threading (diameter and pitch), filter performance and du-
ration. Possible damage may occur to the engine with con-
sequent loss of oil.
MINIMUM TICKOVER
Check at 1000 km (or 1 month).
Every 6000 km (or 6 months).
Carry out this adjustment when the engine is hot.
• Switch on the engine and adjust the tickover as specified by rotat-
ing the accelerator stop screw 1.
Minimum tickover:
1300±1350 rpm
1
1
Содержание Navigator
